KUDI23HB0 KitchenAid Dishwasher - Instructions

Removed bottom rack and replaced axles and wheels, works just like new and did it without any assistance from my son or Husband.

Removed old water tube and replaced it with the new one. Hard part was logistically trying to put it below the rack and it obviously it had to fit very tight and it was quite difficult to get in place, but I did it! Thanks to your easy to use website and excellent service. I was proud of myself for doing the whole job start to finish, and my husband was even more impressed. Only downside to that is that I think he'll be playing more golf, while I do the repair work from now on.

For several years I endured difficulty in pushing in and pulling out a fully loaded lower dishwasher tray in my KitchenAid Superba dishwasher. The tray would "fall out" out of its "track" and jam requiring me to lift up the whole tray to try to pull it out. Then one of the plastic roller "axles" broke and its wheel fell off. So I went on to Part Select's website to find a replacement. When I got it in the mail I replaced the one that broke. I noticed how much more rigid the wheel then ran on its "track." So I replaced all the roller axles and, lo and behold, the lower tray does not jam anymore. It rolls just like new! I am very satisfied. Chris from Bay Ridge, Brooklyn

Took the tube off and noted that there was a factory drilled hole on the underside that lets water drain. I slipped the new tube over the inlet port and the other end over the rotating washing arm aparatus port and everything worked fine. Very easy and fast repair.

First the water tube arrived two days earlier than what I was expecting. I pulled the old tube off and slipped the new tube on by hand. The dishes in the top rack are now a lot cleaner than they have been for the past couple of months. In the future if I need repair parts this is where I will be coming to get them.

I removed clips on the end of the rack, removed the rack, and pulled old tube off. Used plain water as a lubricant to ease replacement of new tube on the dilated end. Very easy!

I was goingto go to Home-Depot, and purchase a short piece of tubing to make the repair.
Just for the "heck" of it, I looked on-line --- and there it was. It is a large diameter thin wall tube, because water presiue is low, almost zero.
However, the replacement part was only $8,25, so I figured, what the heck, I can wait a few days and purchased the part from PartSelect.com. I lubricated the new tube with soap, to make the slip-fit go on easier and -------------- Done

Very easy ......... Thank you

Old roller wheels and axles were broken and already falling off. I simply replaced the roller axles and snapped on the new roller wheels.

Simply inserted the new rubber hose on the two fittings - a couple of minutes at most

I pulled out the old hose and pushed in the new one. Took a little muscle, but was glad that it fit. On line site very helpful with description so that it fit perfectly!

Simply popped on new axles and wheels and dishwasher works like new!

I had repaired the hose with duck tape several times, and finally was able to convince my husband to look up the model number etc. went on line to see if I could locate a dealer to get the hose, and that was so easy,
Ordered it, it came in 2 days, and my dishwasher works great again.

It was so easy just took off the old hose and snapped in the new one.

screwed it in. Closed the door. Voila, it works!

I removed the old tube--I had taped over the hole. I didn't quite have the hand strength to fit over the ends and push the new tube into place. So, my husband did that at both ends without a problem. I'm relying on PartSelect for when I need parts for my 13 year-old appliances.

One of the axles broke off, requiring no removal. The other wheel broke off, but the axle remained. That required squeezing (pliers) to push out. Replacement was easy; just put wheel onto axle and push axle through mounting space. Total: 5 minute job.