KUDI230B0 KitchenAid Dishwasher - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Anne from Sebastopol, CA
- Parts Used:
- 4162321
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Pliers
a couple of axles disintegrated so the bottom dish rack wouldn't roll
I took out the bottom rack, turned it upside down, popped off the wheels and saved them and put on the new axles. It took a little doing to get the new axles snapped into place-they were stiff. I finally figured out how to use the pliers at the right angle to pop them on. Then the wheels popped right on and off I went.
Was this instruction helpful to you?
Thank you for voting!
Rollers came off my bottom rack due to broken axles.
I ordered all new axles even though not all of them were broken - I figured it was just a matter of time. Ordered one new roller because one was missing, and an extra one just in case. Removed all old rollers and axles. A couple of them did not want to come off, so I "hit" them with a screwdriver. Put on all new axles and replaced the rollers. The whole project took about 10 minutes. SUPER EASY. CHEAP FIX FOR MY OLD DISHWASHER.
Was this instruction helpful to you?
Thank you for voting!
Mom died, selling her house. lower rack of dishwasher with only 2 out of 8 wheels
The website had great pictures, I compared the wheels I had and the broken axles with the pictures, and picked what I thought would match. They were perfect. I used pliers to pop the axle on, and my fingers to put on the wheels. It works perfectly now
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Mollie from CANTON, NC
- Parts Used:
- W10586589
- Difficulty Level:
- Very Difficult
- Total Repair Time:
- More than 2 hours
Insulation needed replacing
I searched for the 18x5x5 insulation.,ordered it from Part Select. Waited. Company sent wrong part. Called, they gave me a refund, reordered, promised 2 day free shipping. Waited more than a week, paid for 2 day shipping. Received same, wrong part. Still don't have repair done. Looking elsewhere for part.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Allen from MOUNT VERNON, WA
- Parts Used:
- WP4160355
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
Replacing broken door hinge guide bearing sleeve
Repair was awful without instructions. Instructions were requested twice with no response. Attempted without instruction and broke the sleeve. Reordered but not through Partselect
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Aubrey from BERKELEY LAKE, GA
- Parts Used:
- 675806
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Pliers, Screw drivers, Socket set
The Cutter Spring was totally disfigured and pulled apart. Not functional.
Repair went exactly like the video i watched online. Perfect
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Anita from CAPE MAY, NJ
- Parts Used:
- WP4172117
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Replacement for rusting 40 yr old rack
Tranfered wheels from old rack to replacement rack. Silverware caddy was a bit too big for the replacement. I gently bent the prongs on the rack a little and its fits perfect.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Elmer from YORKVILLE, IL
- Parts Used:
- 675806
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 1- 2 hours
1/4 inch bolt frozen to shaft
The 1/4 inch impeller bolt to shaft would not budge with a nut driver so I had to use a ratchet to loosen it. I could not hold the drain impeller with an adjustable wrench so I had to use a vice-grip. This still did not loosen it so I used an oscillating power saw to cut away at the bottom of the drain impeller being careful to only cut so deep, I didn't want to cut into the motor shaft. Once I had cut some grooves into the drain impeller, I could break it into pieces and remove it. Upon reassembly I tightened the 1/4 inch bolt with the ratchet.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- B Jean from MONTPELIER, OH
- Parts Used:
- WP302711
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers
throwed water out under the door
Did not use the new parts. After removing the spray arm, found a screw out of place. Put the seal ring back in place and the screw back in the hole. Machine works like new.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Eliza from Brooklyn, NY
- Parts Used:
- WP9741853
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
The timer knob had broken. I ordered a new one.
Got it in one day! When I tried to put it on, it didn't seem to quite fit at first, but with a few sharp taps from my rubber hammer it went right on. Works perfectly. Took about a minute for the whole installation.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Walter from KINGSPORT, TN
- Parts Used:
- 675806
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 1- 2 hours
- Tools:
- Nutdriver, Screw drivers, Socket set, Wrench (Adjustable)
i had a leak under the dishwasher when the pump turned on.
I replaced the seals per the video instructions.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Michael from Beverly Hills, MI
- Parts Used:
- 4171544
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Hole in the water delivery tube
Pulled off old tube and slipped on new one.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Ricker from KESWICK, VA
- Parts Used:
- 675806
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 1- 2 hours
- Tools:
- Nutdriver, Screw drivers, Wrench (Adjustable)
noisy
watched a video
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Randall from Ashburn, VA
- Parts Used:
- 9741906
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver, Pliers, Wrench (Adjustable)
Water inlet valve had frozen and cracked
Turn off water and power to the dishwasher. Remove kickboard cover to gain access below the door (2 screws). Water inlet valve was removed using a 5/16 nut driver (1 screw). It is located on the front left side of the dishwasher as you face the appliance. My dishwasher did not need to be pulled out from the cabinet, so using an adjustable wrench removed the supply line. Used a pair of pliers to remove spring clamp on the other line. I then removed the two wires from the clips on the side of the valve. Installation is the reverse, the wires can be reversed with no consequence.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Rosalind from Ithaca, NY
- Parts Used:
- 4171544
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
Dirty dishes discovered water tube old and cracked
Loved how easy it was to deal with you!
Part was clearly pictured and came immediately!
Very satisfying to fix it so easily.
Wondered why we waited so long!
Part was clearly pictured and came immediately!
Very satisfying to fix it so easily.
Wondered why we waited so long!
Was this instruction helpful to you?
Thank you for voting!