KUDH230Y1 KitchenAid Dishwasher - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Elizabeth from Tuscaloosa, AL
- Parts Used:
- 4171566
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
The part fell off and was melted on the drying mechanism in the dishwasher
Just popped the receiver onto the end of the pipe! I am so glad partselect.com had the part and made my job in finding the part I needed so easy!
Was this instruction helpful to you?
Thank you for voting!
bottom drawer roller replacement
Removed the old axles and rollers and snapped in the new ones. Really easy repair.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Judith from Hinton, WV
- Parts Used:
- 4171544
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
dishes remained dirty after completing wash cycle
I removed the rubber water tube before ordering the part. After receiving the part it took less than 2 minutes to replace the part. Now the dishes are clean!!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- DeAnn from New Prague, MN
- Parts Used:
- 4171544
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Easy as pie!
So easy I could do it! I pulled the old tube off (after having dirty dishes for weeks and not realizing it was because of a hole in the hose. When I told my husband I was going to call a repairman, he suggesting ordering the part on line and doing it ourselves - no reason not to! Piece of cake!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Robert from Northport, AL
- Parts Used:
- 4171544
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Pliers, Screw drivers
Dishes in top of washer were not getting clean.
Our diskwasher is over 20 years old. The manufacture did not even list the model anymore. Googled - Kitchenaid parts old. Found your site and order the part on Sat. night. It arrived on Wed. Installed as follows that night.
After reading other reviews on how the job went and seeing that people had problems getting the tube to slide on the outlets I decided to take the rack completely apart so as to have unrestricted access to the connections. Would be easier to work the tube on to them.
First I removed the top rack by releasing the two retainers on the upper rack side rails which hold it up. Then I turned it with bottom up and released all of the plastic clips that held the bottom half of the rack in place. If a clip breaks you can use a nylon cable tie to replace it. Then I took out the screw that holds the metal water bar in place and removed it. Then I took out the screw that holds the plastic part that the water bar was mounted on off. Then with the outlet where the tube was to be mounted not connected to anything it was easy to slide the tube on it. I then was able to slide the tube on to the bracket at the back of the rack. Had to use a screw driver to help get the tube over the round outlet. Then worked it on to where it should be. Reassembled the top rack and put it back on the side rails and washed a load. It worked just like it did when it was new. Saved a service call $75.00 and only took about 30 minutes working at a slow pace.
Love it when everything works like it should.
After reading other reviews on how the job went and seeing that people had problems getting the tube to slide on the outlets I decided to take the rack completely apart so as to have unrestricted access to the connections. Would be easier to work the tube on to them.
First I removed the top rack by releasing the two retainers on the upper rack side rails which hold it up. Then I turned it with bottom up and released all of the plastic clips that held the bottom half of the rack in place. If a clip breaks you can use a nylon cable tie to replace it. Then I took out the screw that holds the metal water bar in place and removed it. Then I took out the screw that holds the plastic part that the water bar was mounted on off. Then with the outlet where the tube was to be mounted not connected to anything it was easy to slide the tube on it. I then was able to slide the tube on to the bracket at the back of the rack. Had to use a screw driver to help get the tube over the round outlet. Then worked it on to where it should be. Reassembled the top rack and put it back on the side rails and washed a load. It worked just like it did when it was new. Saved a service call $75.00 and only took about 30 minutes working at a slow pace.
Love it when everything works like it should.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Debra from Mentor, OH
- Parts Used:
- 4171544
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Dishes in top rack were not getting clean
Took off old hose. It practically fell off.
Used a spoon to widen the ends of new hose and twisted on one end, then other end slipped on. Done!
Used a spoon to widen the ends of new hose and twisted on one end, then other end slipped on. Done!
Was this instruction helpful to you?
Thank you for voting!
Rubber Water Delivery Tube and Upper Spray Arm Receiver
Rubber Water Delivery Tube and Upper Spray Arm Receiver had worn out on my 24+ yr. old Kitchen Aid Dishwasher. First time anything every had had to be done to this machine. It has been a work horse and still works great. The above parts had simply worn out. I found this site online and sent for the parts. My husband replaced them and followed the instructions of greasing the parts when replacing them. The job was done in minutes and the washer is working fine again.
The parts were shipped promptly and we had them in a matter of two or three days. Great experience with this company and will use again if the need arises.
The parts were shipped promptly and we had them in a matter of two or three days. Great experience with this company and will use again if the need arises.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Charles from Eagle River, AK
- Parts Used:
- 4171544
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Rubber water tube to upper rack had begun to decompose
I pulled off the remains of the old tube and simply slipped the new hose on by hand. Easy as pie!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Howard from Boynton Beach, FL
- Parts Used:
- 350930
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver
Both outside door handles turned very beige
Everything worked perfectly---thanks to the suggestion of your call center agent. She suggested that since the replacement door handles were no longer available, I should consider repainting them--it worked like a charm. Please tell her she was a life saver. We rent that house in Fl and my returning tenants had complained about the discoloring refer handles. Thank you
Was this instruction helpful to you?
Thank you for voting!
Roller axles dried out and brittle and broke
Removed bottom rack and replaced axles and wheels, works just like new and did it without any assistance from my son or Husband.
Was this instruction helpful to you?
Thank you for voting!
Tube cracked and split
Pulled off old tube and upper arm receiver.The new tube and the section it was to go on appeared to be too small. I heated new tube with hair blower and streched new tube so as to fit .
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Edward from Winchester, MA
- Parts Used:
- 4171544
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
Tude was disintegrating.
Removed old tube.
New tube was a little tight, so I heated it with a hair dryer and used dish washing detergent - Joy - as a lubricant. Then the tube slipped on easily.
New tube was a little tight, so I heated it with a hair dryer and used dish washing detergent - Joy - as a lubricant. Then the tube slipped on easily.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Alan from Spooner, WI
- Parts Used:
- 4171544
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
water tube split and fell on drying element
Removed old tube, moistened both ends of new tube with hot water and slid over inlet and outlet holes. Repair done!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Janice from Napa, CA
- Parts Used:
- 4171544
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Dishwasher not cleaning as rubbr water tube cracked
I removed clips on the end of the rack, removed the rack, and pulled old tube off. Used plain water as a lubricant to ease replacement of new tube on the dilated end. Very easy!
Was this instruction helpful to you?
Thank you for voting!
Rollers and axels were worn out.
Very easily!! I am 19 years old and repaired the dishwasher for my grandmother in about 15 minutes. Great products.
Was this instruction helpful to you?
Thank you for voting!