KDFE104DSS0 KitchenAid Dishwasher - Instructions

Took off the old wheels and placed them on the new rack - fast and easy if you watch the video.

unplug, disconnect water, remove all screws holding the machine in the cabinet. slide out the machine to access the 4 bolts hold the rail. Have a prop to hold basket in place as you remove old rail> Plastic clips front and back, hold the basket to the rail. Be careful not to break, not include with the replacement rail. If you are not handy with tools and no insight...hire it done

Initial inspection of the issue and research suggested the door latch was malfunctioning / broken. I bought the part and expressed it home. The installation involved removing the door screws on the inside of the door, separating the front and back panels, unplugging the door latch, removing it from its niche and popping in the new one. Reverse the take apart and it was done. Very simple swap. Hardest part was juggling the two halves of the door and preventing the door for trying to close in the process as the bulk of the weight is in the outside half of the door.

The new part did not fix the issue. The door strike was the next part that could be broken / malfunctioning. I ordered that part as well and replaced it. In the process of replacing it I found that the original door strike had been installed upside down. I am guessing it was installed at just the right pitch, or maybe even bent at the manufacturing facility, so that it latched. No idea how it managed two years like that. I installed the new one correctly and the door latches perfectly. Both parts I removed from the unit I will retain if my new parts should fail in the future.

I had a common issue on many dishwashers, the final drain cycle was not draining but the pump was trying to turn. Also, the drain pipe was clean. This issue caused a burning smell, like a circuit board heating up. Half plastic smell, half electrical. I bought a replacement pump, followed the pump replacement video instructions from PartsSelect, and it was replaced in under 15 minutes without any tools.

Removed broken tin row. Replaced with new tine row. Tokk less than 1 minute.

We watched videos on this repair but they didn't matter. All we did was remove the lower rack of the dishwasher. To remove the broken assembly we put pressure behind the wheels pulling them out and up - it popped right off. To install the new wheel assembly, it was easy to see where to align the part and my husband snapped it back in. No tools. Easy peasy.

Ordered a new pump (after a online diagnosis). Followed the instruction video on the website...also took the time to replace the discharge hose due to residue buildup...tested dishwasher (one cycle). Slide dishwasher back into opening....DONE. Works perfectly. THANKS

leveled dishwasher, it was leaning forward, raised front 1/2'", to get level.
no More leaks, WOULD LIKE TO RETURN DOOR SEAL. DID NOT USE SEAL.

THANKS,
PETE GODSHALK

Due to the way I installed the appliance originally it was not necessary to disconnect supply water nor the drain connections. When the cord broke the spring came out of the point of connection to the appliance. It some "finagelling" to reattach the spring.After some "select vocabulary" it hooked into the correct spot and the rest was history.

I took the valve off and actually hooked 110 volts to the vale and tried to blow through it and it would not let air pass through it. I replaced the the new valve in about 15 minutes and it works fine

Turned off water supply to the unit. Removed plastic cover at bottom front. I only had to disconnect the copper water line to slide the unit about 1/3 of the way out. I then was able to reach the wires, disconnect them and use a stubby box/open end wrench (5/8? don't remember for sure) to remove the plastic nuts. I then opened the door, removed the bottom basket and slipped the element right out. Installation of new part was reverse.

Upper tray removed and each rack adjuster removed and replaced one after the other. Only tool was screwdriver. Only knowledge was from the online videos. Only took 30 minutes or so. The repair could have been done more quickly if I wasn't fearful that the smaller plastic parts would break when pulled or pried away from the rack adjuster. The only mistake was not making sure the adjuster tabs were fully engaged in back and clicked in the front attachment.

There was no tools involved the part popped right into place. I received the part within two days from the date placed. It was great.

First remove the front kick panel by removing 2 philips screws. Turn off the water supply, and then disconnect the supply line if not of the flexible kind. Mine was copper. Remove 2 screws holding dishwasher to counter top and pull machine out. Open door and attach replacement link by hooking the plastic end to the hinge hook on the door side and then place the string portion round the plastic pulleys and then attach the other end of the link to the end of the spring attached to the rear of the machine along the bottom side. Push dishwasher back into position, reattach supply line and re-install both screws attaching the machine to the counter top. Turn on the water supply and check for leaks. Place the kick plate into postion and secure using the 2 philips screws that were removed.

Had to remove 2 screws fastening dishwasher to counter. Also removed bottom faceplate to expose the legs and to be able to lower them. Other sites recommended disconnecting the drain and water line but I did not have to do that, I had enough slack in the lines. I got the dishwasher about halfway out of the cabinet and then was able to remove the 4 screws holding the right track. Put the new track in and was good to go. Problem was that the left track broke and fell off a few days later. Still was an easy fix and thanks to PartSelect it was not very expensive.