KDTE704DWH0 KitchenAid Dishwasher - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Robert from Highland Village, TX
- Parts Used:
- 8194001
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
The Door Leveler Nylon Cord assy broke
It was very easy.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Marta from ENNIS, TX
- Parts Used:
- WPW10546503
- Difficulty Level:
- Very Easy
- Total Repair Time:
- 15 - 30 mins
My upper rack adjuster broke
I ordered the part from this website and easily replaced it.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- paula from ASHEVILLE, NC
- Parts Used:
- WPW10531320
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
The drain Pump failed
Took the kick plate off without removing the the machine.
Reached in and turned the existing pump to loosen it. Then disconnected the wire.
Reversed the process to install the new pump.
Reached in and turned the existing pump to loosen it. Then disconnected the wire.
Reversed the process to install the new pump.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Raymond from WICHITA, KS
- Parts Used:
- W11259786
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers, Socket set
Spot welds on track rusted and broke.
Pulled out dishwasher, removed 4 bolts holding the track to the dishwasher, replaced track and installed the 4 bolts. Pushed back the dishwasher and works like new. The new tracks are riveted instead of spot weld and will last longer.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Edna from WEST MONROE, LA
- Parts Used:
- WPW10653840
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
When cycling through it would stop up to 3 times & have to be restarted.
Replaced door latch
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Jonathan from DOWNS, KS
- Parts Used:
- 4317824
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Pliers, Screw drivers, Wrench (Adjustable)
Someone had used the wrong type of power cord
Recently bought a whirlpool dishwasher, the dishwasher was converted to a portable dishwasher and they did not use the cord application power cord so they machine was blowing our breaker, instructions were very simple and installation was easy!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Ronald from VAN BUREN TWP, MI
- Parts Used:
- 4317824
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
none
removed and installed cords with screw driver
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- LOUIS from RAYNE, LA
- Parts Used:
- WPW10082853
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
The original Tine Pivot had broken
I looked at the position of the remaining Tine Pivot, since there are four on this dishwasher upper rack, and positioned the replacement pivot and pressed it into place. It was a snap (excuse the pun!). NOTE: My dishwasher's Model Number was not in the list provided herein. I had to search a couple of models to find the Upper Rack that looked like ours and to find the Tine Pivot replacement part that looked like ours.That process took longer than the "repair".
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Kathleen from DUBLIN, CA
- Parts Used:
- WPW10531320
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Socket set
We found pieces of glass in the drain pump
Our new drain pump arrived with 2 clips broken. So we switched the housing with the old pump and installed
Used youTube video for step by step instructions
Used youTube video for step by step instructions
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Cassie from RIVERDALE, CA
- Parts Used:
- WPW10546503, WPW10250162
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
Replacing broken adjuster housing cover.
Take out the upper dishwasher rack. Place the adjuster towards the back of the upper each place attachment clips to secure adjuster and the adjuster clips to the back of the housing. Check to back sure adjuster move up and down and click back into place. Your installation is complete. Good luck!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Amy from Green Bay, WI
- Parts Used:
- WPW10546503
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers
The left side was drooping so couldn’t use the dishwasher
Removed the upper rack and replaced both side with new upper rack adjusters that are now metal and not plastic!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Eladio from LOGAN, OH
- Parts Used:
- WPW10538166
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 1- 2 hours
- Tools:
- Nutdriver, Screw drivers, Wrench (Adjustable)
Develeoped a leak on the bottom.
Pulled dishwasher out of compartment, removed all parts underneath. removed inner parts, removed pump assembly. Installed new pump assembly and grommet. Reassembled in reverse order, test ran and unit was operating normal and no leaks.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Thomas from PHOENIX, AZ
- Parts Used:
- WPW10546503
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 1- 2 hours
- Tools:
- Screw drivers
Left-side rack adjuster broke, so upper rack couldn't be used properly.
Per suggestions from other reviews, I looked for You Tube videos for replacing this part. The video I used was completely necessary, but moved way too fast, so required lots of stopping, rewinding and starting again. But I managed to get the old rack adjuster removed and the new one installed without too much trouble.
Then I tried installing it in the pull-out rail. The front connector on the new adjuster would not fit into the appropriate slot. Initially I thought maybe the part was defective, but determined that the dimensions were as accurate as my eye and tape measure could evaluate. Finally, I settled on the expedient of filing away at least 1/16" from one edge of the slot so that the connector would drop into place.
Not sure why this discrepancy existed but the problem appears to be resolved.
Then I tried installing it in the pull-out rail. The front connector on the new adjuster would not fit into the appropriate slot. Initially I thought maybe the part was defective, but determined that the dimensions were as accurate as my eye and tape measure could evaluate. Finally, I settled on the expedient of filing away at least 1/16" from one edge of the slot so that the connector would drop into place.
Not sure why this discrepancy existed but the problem appears to be resolved.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- robert from SOUTH HADLEY, MA
- Parts Used:
- WPW10497235
- Difficulty Level:
- Very Easy
- Total Repair Time:
- 30 - 60 mins
Dishwasher was leaking at the bottom edge of door.
Ordered the door gasket and replaced it. Worked perfect. The trick was to stretch the gasket a little as it went around the top curvatures. It would stick out some and not sit as flat as on the top and sides. This helped it to flatten down better.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Nancy from BLOOMINGTON, IN
- Parts Used:
- W10537869
- Difficulty Level:
- Very Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver
Leaking dishwasher
Turned the dishwasher in its side. Used the video step by step. This is why we purchased from this site
Was this instruction helpful to you?
Thank you for voting!