KDTM404EBL2 KitchenAid Dishwasher - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Amy from Green Bay, WI
- Parts Used:
- WPW10546503
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers
The left side was drooping so couldn’t use the dishwasher
Removed the upper rack and replaced both side with new upper rack adjusters that are now metal and not plastic!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Eladio from LOGAN, OH
- Parts Used:
- WPW10538166
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 1- 2 hours
- Tools:
- Nutdriver, Screw drivers, Wrench (Adjustable)
Develeoped a leak on the bottom.
Pulled dishwasher out of compartment, removed all parts underneath. removed inner parts, removed pump assembly. Installed new pump assembly and grommet. Reassembled in reverse order, test ran and unit was operating normal and no leaks.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Robert from PORT LUDLOW, WA
- Parts Used:
- W11177741, WPW10653840
- Difficulty Level:
- Difficult
- Total Repair Time:
- More than 2 hours
- Tools:
- Screw drivers
Water leaking around door and latch mechanisim seems to have failed
Still not sure it is repaired. Still have water leakage around upper edge of door on control data panel. We just experienced an issue with the auto drain system, the first since door seal repair and door latch replacement???? Is the latching mechanism suppose to secure the door?
If so it isn't?
Not a great success story. A new washer may be in the cards
If so it isn't?
Not a great success story. A new washer may be in the cards
Was this instruction helpful to you?
Thank you for voting!
PartSelect Scammers
PartSelect intentionally shipped obsolete part that could not possibly fit a dishwasher. The part looked to be a rectangle door seal for a freezer/ref. You make it impossible to return the part. I find it interesting that you sent the correct install video and wrong part.
Suggestion: After you print a shipping label take a picture of the part and shipping label before it is boxed. The customer should not have to send you a picture of the wrong part and the serial number of the appliance for a refund. You did not need the serial number to ship it.
I will never use your company again William Dewberry
Suggestion: After you print a shipping label take a picture of the part and shipping label before it is boxed. The customer should not have to send you a picture of the wrong part and the serial number of the appliance for a refund. You did not need the serial number to ship it.
I will never use your company again William Dewberry
Was this instruction helpful to you?
Thank you for voting!
Top rack kept coming off the left slide track
I followed the video and even though my dishwasher was slightly different from the one shown, everything worked well. I was lucky that I had enough clearance to pull the dishwasher away from the countertop far enough to make the repair, without having to remove any dishwasher wiring below. I replaced both side tracks, even though only the left side was broken.
Was this instruction helpful to you?
Thank you for voting!
Dish rack slide arms losing ball bearings
Unscrewed mounting screws, pulled dishwasher out halfway, replaced arms, 4 screws each side .....very simple 30 min tops. Parts perfect and quick delivery!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Cassie from RIVERDALE, CA
- Parts Used:
- WPW10546503, WPW10250162
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
Replacing broken adjuster housing cover.
Take out the upper dishwasher rack. Place the adjuster towards the back of the upper each place attachment clips to secure adjuster and the adjuster clips to the back of the housing. Check to back sure adjuster move up and down and click back into place. Your installation is complete. Good luck!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Robert from Des Moines, IA
- Parts Used:
- 8269144A
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver, Pliers, Screw drivers, Wrench set
Dish washer was very smelly.
After replacing garbage disposal. I referred to you video you sent me when i received the new replacement hose. That made it look very easy to install. Thank you for all your help and support.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Fred from SICKLERVILLE, NJ
- Parts Used:
- 4317824
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver, Screw drivers
Intermittent power loss
Remove power source, then remove old power cord.Run new power cord through existing opening ang attach to existing power box on bottom o f dishwasher. Install electrical leads and device ground. Reinstall cabinet bottom. Check out operation by running a cycle. All ok!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Greg from KENT, OH
- Parts Used:
- W10861000
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers
Worn out detergent dispenser
Total repair time after watching videos was 53 minutes. I estimate I saved between $200 to $300 by doing this myself. If you have any DIY skills, don't hesitate to replace the detergent dispenser yourself.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Mark from Galveston, TX
- Parts Used:
- WPW10082853
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
Missing tine pivot
Pushed to be into place
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Steven from RIVERSIDE, IL
- Parts Used:
- W11175771
- Difficulty Level:
- Very Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Pliers, Screw drivers, Socket set
The Inlet Valve cracked from the severe cold weather we had in Chicago area.
Removing and installing the new part was fairly simple. We removed the water hose first since it is the easiest to see. We then removed the screw holding the part to the metal frame. We slid out the part out of the holder to remove the black hose and electric plug (it is like the old phone jacks). After it was completely off we plugged in the electric to the new part which was very easy since it can only go in one way. We slid the new part in place and attached the black hose. We attached the piece to the frame with the one screw and last we attached the gold (garden hose) connection. We turned on the water to look for any leaks then turned the power on and ran it through a partial rinse to be sure there were no leaks.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Carol from Scottsdale, AZ
- Parts Used:
- WPW10082853
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
A bracket was missing on the top rack of dishwasher
Easy. Part just snapped in and took all of about a minute. Now the top rack doe snot slide back and forth.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Joel from ROLLA, MO
- Parts Used:
- WP8269145
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Pliers, Screw drivers
installer from lowes di not do it right, forgot to put scew in, instead he used shims, as usuall no more installs from Lowes
followed directions, a kid could have done it,
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- edward from sullivan, OH
- Parts Used:
- 8194001
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
Door of the dishwaher banged open
Pulled the dishwasher out and took the two door balance links off and put the new ones on and attached to the spring. It was very quick and easy
Was this instruction helpful to you?
Thank you for voting!