KDFE104DWH5 KitchenAid Dishwasher - Instructions

It was easy to remove the old parts by using a screwdriver to push in “tabs” that kept retainer clips in place. Once removed, it was a matter of easy assembly in reverse and then re-clip. It became clear that the problem was because a few tabs that click into the sliding track and worn to the point where they no longer retained a tight connection to the track causing the upper rack to tilt with weight to front or back. Sure, the parts are a bit pricey but not when compared to a repair visit or a new KitchenAid which otherwise was functioning perfectly.

Pulled off old seal. Pressed into groove the new door seal. No parts required.

1) clear out the dishwasher
2) remove unit securing screws from top or sides of DW and cabinetry near the top or under the counter top
3) gently pull the dishwasher from the cabinetry about 20" is plenty, mind the connecting hoses and electrical connection
4) close the door! pull back the insulation from the area of the hinge and photograph both sides - this will save you the pain of going online
5) you will see the cord, the tensioning wheel assembly and the door balance spring on both sides
6) with the door closed to relieve tension on the cord, remove the cord from the balance spring - this can be done w/o tools at this point
7) remove the 5/16" screw from the plastic tensioning wheels and remove the tensioners, cord - leave the springs in place if not replacing them
8) install the door end of the cord to its hook on the hinge, install the new tensioning wheel assembly, install the old 5/16" self tapping screw through the lower wheel and into the outer hole in the frame
9) thread the cord from the door over the upper wheel and lower wheel. the lower wheel has cord retaining tabs to hold the cord on the assembly
10) hook the eye end of the cord to the balance spring and you are finished with the first side - repeat operations for the other side, reposition the insulation and slide the washer back in its cavity - do not forget to reinstall the stabilizing screws in the upper washer frame
11) you've done it!
12) have a cuppa and do your second washer that hasn't failed yet - it will soon.

I did not relize that the drain hose was in two parts. Naturally I ordered the wrong half. So after I relized my mistake, I re-ordered the correct part. Once the correct part was received the repair was easy and went well.

Unplug dishwasher and slide it out from under cabinet. Remove old broken link (a heavy string between two plastic parts) and replace with new one. Slide dishwasher back and plug it in. Very easy and no tools required.

The old tine row came out easily and the new one was easy to pop into place. I was pleased that it was so easy to order a replacement part.

repair went smooth for the grommet. suggest a small of vasoline to ease installation of grommet

Searched internet found a YouTube video not quite the same model but close enough to get me going and the steps were the same

Hardest part was figuring out how to release and remove upper rack as mine did not match the instructions. After that is was tricky but not overly difficult. The instructions on-line did not make sense, but it all was fairly intuitive process. Take some before pictures, lol. Dishwaswasher works great.

I removed and reinstalled the new gasket per the video instructions, but I found the corners to be much harder to install than indicated. I finally used a large, flat, dull screwdriver to carefully push the gasket all the way in, and used my fingers to feel whether the gasket was all the way in. I figured if the gasket wasn't all the way in, I would have a leak at the bottom of the door because the top of the gasket would stick out farther than the bottom, which is exactly what the original symptoms were. Perhaps I didn't need a new gasket? There was no visible damage. Pushing in the corners of the original gasket may have fixed it, but the new gasket worked perfectly! Thanks, Part Select!!

Remove 2 screws on lower baseplate. Remove 2 screws that hold dishwasher inside cabinet( may be attached to counter top or side cabinets). Turn off water supply to dishwasher. Remove any connections such as water supply, electrical connection, or waste water line that prevent dishwasher from being pulled out about 3/4 of the way. With the dishwasher door closed, remove broken parts and replace with new parts. Pull on spring to make final connection of nylon cable. Reverse the above instructions for re-installing the machine.

put new hose on, very easy.

The water valve float lever was broke. So I replaced that and the water level switch. Probably didn’t have to replace switch. Very easy!!

Installed new pump from the front. Power off remove front cover reached my hand behind pump for release clip, push down turned counter clockwise pump comes out. Disconnected electrical plug attached plug to new pump. Put pump in at 45 degrees rotated clockwise until hear clip lock in . Tested then replaced cover

Removed screws holding dishwasher in place. This dishwasher has one one the left and right side after you open the door hidden behind a plastic hole cover that you can pry out of place with a putty knife or some other thin tool. After this pull the dishwasher out about halfway and there are 4 screws on each side of the dishwasher (on the outside) that hold the top track assemble. Just unscrew these with the appropriate sized socket, remove the old track and screw in the new track. Super easy. Anybody can do this.