KUDL15FXWH7 KitchenAid Dishwasher - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- George from LYMAN, ME
- Parts Used:
- WPW10463906
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
The old filter was warped, allowing food into the sprayer system
Replaced the strainer. This keeps the two sprayers clean/clear so they do not clog up. Dishes are cleaner now. Note : if your sprayers are clogged it is a long process to clear out the sprayers. Dishes will not be clean until your sprayers are all cleared.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Lois from Great Falls, MT
- Parts Used:
- WP3400918
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
two retainers broke and the main part fell apart
pushed the new retainers in the holes and we are set to go
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Paul from CANONSBURG, PA
- Parts Used:
- WPW10531320
- Difficulty Level:
- Very Easy
- Total Repair Time:
- 15 - 30 mins
Drain pump flange broke
Laid on my side amd reach under unit
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Jane from JOLIET, IL
- Parts Used:
- W10195416
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Replaced wheels on lower rack
My husband did the repair. It was very easy. He basically just popped off the old wheels and popped on the new ones.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Randy from Tucson, AZ
- Parts Used:
- WPW10327249, WPW10195039
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Door leaking
Float switch right in front. Did not remove dishwasher. Used small flat screwdriver to un clip cover. Very soft and easy. Unplug and it slides out.
Same with the water inlet. Did not remove and used a screwdriver and small channel locks. Turn off water. Remove hose and remove screw. Slides out. Very easy.
Same with the water inlet. Did not remove and used a screwdriver and small channel locks. Turn off water. Remove hose and remove screw. Slides out. Very easy.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Henry from COLORADO SPGS, CO
- Parts Used:
- W10728863
- Difficulty Level:
- Very Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
Replacing the lift/roller mechanism on dishwasher upper tray
Following the video was quick and easy. Without the video it would have been slow and painful.
Was this instruction helpful to you?
Thank you for voting!
Original door balance cord broke on one side
pulled the dishwasher out (took the most time-1 hour) and 30 min. to install new door balance kit and springs. Replace both sides while the unit was out.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Martha from SAN DIEGO, CA
- Parts Used:
- W10872845
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
Water filter needed replacing
The old filter simply unscrews and the new one screws in.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Sherry from SUSANVILLE, CA
- Parts Used:
- WPW10491331
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
The filter came out and pushed the arm up on the burner and melted it.
The air just unscrews with one twist and the new arm twist right back on. No tools needs. Saved me $100 service call.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Steve from BUFFALO GROVE, IL
- Parts Used:
- W10727426
- Difficulty Level:
- Easy
- Total Repair Time:
- 1- 2 hours
Broken tine rows on upper basket
Popping out the old tine rows was very simple and required no tools. The only issue was that the spacing of the replacement tines was different from the original parts and there was not enough space between the tines and the basket to snap the clips back on to hold the tine row. I went to my band saw and cut the extended ends off of the clips and then they snapped into place perfectly. This would have been a 20 minute, no tool job if I didn't have to run to the band saw.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- robert from SOUTH HADLEY, MA
- Parts Used:
- WPW10497235
- Difficulty Level:
- Very Easy
- Total Repair Time:
- 30 - 60 mins
Dishwasher was leaking at the bottom edge of door.
Ordered the door gasket and replaced it. Worked perfect. The trick was to stretch the gasket a little as it went around the top curvatures. It would stick out some and not sit as flat as on the top and sides. This helped it to flatten down better.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Richard from TRUCKEE, CA
- Parts Used:
- WPW10505748, WPW10350401, WPW10195622
- Difficulty Level:
- Very Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers, Wrench (Adjustable)
Fully loaded top rack would detach from track when pulled out for emptying.
Removed dishwasher from cabinetry to replace tub rollers (4). Replaced roller sets (4) on top rack. Also replace both rails and rail stops. Screwdriver was only tool required for this part of repair. Needed wrench and screwdriver to remove and replace dishwasher in lower cabinetry.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Douglas from SAINT JOHN, IN
- Parts Used:
- WPW10531320
- Difficulty Level:
- Very Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver, Pliers
Dishwasher was making a moaning sound when draining.
Unplug dishwasher. Remove lower front accessible panel. Disconnect wires to the drain pump. Rotate pump to unlock and remove. Apply plumbers grease to rubber seal and install new pump. Connect wires. Plug in dishwasher and run rinse cycle to check for no water leak. If all okay replace access panel. Done.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Peter from LEBANON, NJ
- Parts Used:
- WPW10497235
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
door leaks bottom right
leveled dishwasher, it was leaning forward, raised front 1/2'", to get level.
no More leaks, WOULD LIKE TO RETURN DOOR SEAL. DID NOT USE SEAL.
THANKS,
PETE GODSHALK
no More leaks, WOULD LIKE TO RETURN DOOR SEAL. DID NOT USE SEAL.
THANKS,
PETE GODSHALK
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Bryca from TULSA, OK
- Parts Used:
- WPW10653840
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Pliers
Dishwasher door stopped latching properly.
Initial inspection of the issue and research suggested the door latch was malfunctioning / broken. I bought the part and expressed it home. The installation involved removing the door screws on the inside of the door, separating the front and back panels, unplugging the door latch, removing it from its niche and popping in the new one. Reverse the take apart and it was done. Very simple swap. Hardest part was juggling the two halves of the door and preventing the door for trying to close in the process as the bulk of the weight is in the outside half of the door.
The new part did not fix the issue. The door strike was the next part that could be broken / malfunctioning. I ordered that part as well and replaced it. In the process of replacing it I found that the original door strike had been installed upside down. I am guessing it was installed at just the right pitch, or maybe even bent at the manufacturing facility, so that it latched. No idea how it managed two years like that. I installed the new one correctly and the door latches perfectly. Both parts I removed from the unit I will retain if my new parts should fail in the future.
The new part did not fix the issue. The door strike was the next part that could be broken / malfunctioning. I ordered that part as well and replaced it. In the process of replacing it I found that the original door strike had been installed upside down. I am guessing it was installed at just the right pitch, or maybe even bent at the manufacturing facility, so that it latched. No idea how it managed two years like that. I installed the new one correctly and the door latches perfectly. Both parts I removed from the unit I will retain if my new parts should fail in the future.
Was this instruction helpful to you?
Thank you for voting!