KUDX23HB0 KitchenAid Dishwasher - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Robert from Schaumburg, IL
- Parts Used:
- 4171544
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
old water tube became brittle and split down it's length
Removed by hand the old water tube and pushed the new tube on. It was no big deal. Itook about 3 mins.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Scott from Orland Park, IL
- Parts Used:
- 4171544
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Cracked water tube
I was goingto go to Home-Depot, and purchase a short piece of tubing to make the repair.
Just for the "heck" of it, I looked on-line --- and there it was. It is a large diameter thin wall tube, because water presiue is low, almost zero.
However, the replacement part was only $8,25, so I figured, what the heck, I can wait a few days and purchased the part from PartSelect.com. I lubricated the new tube with soap, to make the slip-fit go on easier and -------------- Done
Very easy ......... Thank you
Just for the "heck" of it, I looked on-line --- and there it was. It is a large diameter thin wall tube, because water presiue is low, almost zero.
However, the replacement part was only $8,25, so I figured, what the heck, I can wait a few days and purchased the part from PartSelect.com. I lubricated the new tube with soap, to make the slip-fit go on easier and -------------- Done
Very easy ......... Thank you
Was this instruction helpful to you?
Thank you for voting!
roller wheels & axles broken
Old roller wheels and axles were broken and already falling off. I simply replaced the roller axles and snapped on the new roller wheels.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Daniel from Lorain, OH
- Parts Used:
- 4171544
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Worn out rubber delivery tube
Slipped old one off slid new one on . Took about one minute. Held well and is washing so much better now.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- robert from glenmoore, PA
- Parts Used:
- 4171544
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
worn rubber tube water feed to upper spin arm in dishwasher
The replacement worked fine, but the website could have been a bit more re-assuring in terms of showing the image of the part. It was not possible on the website to determine whether the piece was going to fit, as the piece as shown was flat/oval on both ends, where the fitting for the water feed is round. The site could have explained that this was flexible material that would form itself to the round feed connection. The measurements of the part should also be given. The price was right, so I bought it anyway, and hoped. As I have said, it DID work fine. You need to clarify the item on the website.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Barbara from Santa Rosa Beach, FL
- Parts Used:
- 4171544
- Difficulty Level:
- Easy
- Total Repair Time:
- Less than 15 mins
The old tube was worn out and had holes
Took the old one off then used canola oil to put on the inside of the tube and it went on easy.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Sherrie from Mount Kisco, NY
- Parts Used:
- 4171544
- Difficulty Level:
- Easy
- Total Repair Time:
- Less than 15 mins
Cracked water delivery tube
Replaced the tube. It was relatively easy although it did take a small bit of squeezing/reshaping the newer rubber tubing to get it to fit on the outlet (it was a bit snug.)
Was this instruction helpful to you?
Thank you for voting!
Replace 2 Wheels
One of the axles broke off, requiring no removal. The other wheel broke off, but the axle remained. That required squeezing (pliers) to push out. Replacement was easy; just put wheel onto axle and push axle through mounting space. Total: 5 minute job.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Barbara K. from Lorain, OH
- Parts Used:
- 4171544
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- Less than 15 mins
Hose kept slipping off - stretched out of shape from use and age.
Used a heat gun (or hair dryer could probably work)to stretch the ends of the hose to slip over areas to connect.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Robert from Rancho Plaos Verdis, CA
- Parts Used:
- 4171544
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- Less than 15 mins
The tube on the top split
Our old Kitchenaid Dishwasher was not getting the glasses on the top shelf clean. I looked and found the tube running to the washer arm under the top basket was split.
I replaced the tube. First I put dish soap in the ends of the new tube, so they slipped onto the other parts with only moderate force.
Now the dishwasher is making the glasses in the top basket clean again.
Regards,
Bob
I replaced the tube. First I put dish soap in the ends of the new tube, so they slipped onto the other parts with only moderate force.
Now the dishwasher is making the glasses in the top basket clean again.
Regards,
Bob
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Merdell from Montgomery, TX
- Parts Used:
- 4171544
- Difficulty Level:
- Easy
- Total Repair Time:
- Less than 15 mins
hole in the tube, wear and tear on it
I removed the old tube--I had taped over the hole. I didn't quite have the hand strength to fit over the ends and push the new tube into place. So, my husband did that at both ends without a problem. I'm relying on PartSelect for when I need parts for my 13 year-old appliances.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Terrance from Burlington, VT
- Parts Used:
- 4171544
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Hose was badly cracked from old age
I removed the upper rack from the dishwasher by popping the two rack track stops out of the rack tracks. The old tube came off easily, and the new tube went on very nicely, after lubing each end with a dab of liquid dish soap. I put the rack back on its tracks , popped the track stops back in and my dishwasher was back in business.
Was this instruction helpful to you?
Thank you for voting!
A roller came off the bottom washer tray in the dishwasher because of broken axle
I removed the broken axle with the help of a small screwdriver and replaced it with a new one. Then I installed a new roller, which was easy because all I had to do was push it on with my fingers.
One of the easiest repairs I've ever made on anything and now I'm happy because my wife is happy!
One of the easiest repairs I've ever made on anything and now I'm happy because my wife is happy!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Richard from Bozeman, MT
- Parts Used:
- 4171544
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
dry rotted rubber tube
pulled off the old and put on the new. Great pictures on website so I got the right part the first time. Thanks!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- James from Sagamore Hills, OH
- Parts Used:
- 4171544
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
The rubber hose running to the upper shelf discharge fan rotted out.
It was 94 degrees that day so I set the rubber hose outside in the sun to loosen it up, make it more plyable. I then mixed up some soapy water and doused the ends of the hose with the soapy water and slid the hose right onto the fittings.
There was a small hole in the hose which was not discussed in the directions. I assumed the hole should be installed on the down side to let water drain out after the dishwasher is finished. This will reduce the chance of bacteria building in the hose.
I read the installation tips before I started and picked up the soap mix and heating up the hose before installation. Can be accomplished with a hair dryer if it is not 94+ degrees outside!!!
Thanks,
Jim
There was a small hole in the hose which was not discussed in the directions. I assumed the hole should be installed on the down side to let water drain out after the dishwasher is finished. This will reduce the chance of bacteria building in the hose.
I read the installation tips before I started and picked up the soap mix and heating up the hose before installation. Can be accomplished with a hair dryer if it is not 94+ degrees outside!!!
Thanks,
Jim
Was this instruction helpful to you?
Thank you for voting!