KDSS21 KitchenAid Dishwasher - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- David from Middleton, WI
- Parts Used:
- 279570
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Dryer door would not close and latch on both catches w/o pushing them shut individually.
Our make/model was not on the online instruction, but it was similar. Ours had a glass (plastic)front window in the door. To remove the top catch you had to take out the top four screws that hold the door together (philips head screws) allowing you to pull back the gray plastic strip to access the top latch, then replace it like in the online directions using a needle nose pliers. The bottom catch, once the two remaining the screws were out gives you access to the bottom catch. Remove it with the pliers and snap the new ones into place. You can completely take out the window when you replace the bottom latch if you want.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Tonya from Aberdeen, MS
- Parts Used:
- 279570
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
The latch at top came off.
It snapped right in. Works perfect.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Patrick from Sanford, NC
- Parts Used:
- 279570
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Pliers, Screw drivers
Door keeps opening while clothes are drying
I watched the video and after that made the repair, it was very easy and the video was a really big help. From start to finish it took me no longer than 10 minutes.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Richard from Marmora, NJ
- Parts Used:
- 279570
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
door would not close catch fell within the door
Pushed the new catch in by hand. Working great.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- David from Carlisle, PA
- Parts Used:
- WP4162568
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Pliers, Screw drivers
Soap Cup Lid was not opening during main wash cycle
Very easy. Disconnect power to the dishwasher via a breaker or fuse. Open the door and remove just the 4 screws on the inside lip of the door. Do not remove the screws hoding the closing brackets. Remove the front glass and chrome panel between the control panel and the kick panel. This will give you access to the soap cup and bi-metal. Remove the one retaining screw and remove the bi-metal,taking note of the position of the wires. Remove the wires, by grasping the connectors (I used needle nose pliers for this), not the wires, and re-intsall them on the new bi-metal. Re-install bi-metal on soap cup assembly, "cock" the release lever by closing the soap cup cover and manually trip the bi-metal to make sure it will release the lever and open the cover. Re-install the front panel with screws. Restore power and test appliance.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Linda from Eagle Bridge, NY
- Parts Used:
- 326789
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Pliers
old burner unit needed replacing
Isimply pulled the old burner unit and followed the instructions that came with the replacement.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- George from Melbourne, FL
- Parts Used:
- 279570
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Pliers
dry door latch broke
I watched the online video first, which made the removal and installation fast and easy.
Was this instruction helpful to you?
Thank you for voting!