KDSS21 KitchenAid Dishwasher - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Susan from WARREN, NJ
- Parts Used:
- 279570
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Dryer door latch broke and door wouldn’t stay shut.
Jimmied out the latch using two screw drivers to get under the edges. Pushed the new piece in. Voila! Took 2 minutes for what my repair man told me would cost about $200 to fix. Unbelievable!!( I first watched some YouTube videos to get the idea )
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- James from Fort Collins, CO
- Parts Used:
- WP8189867
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 1- 2 hours
- Tools:
- Pliers, Screw drivers, Wrench set
light wont come on
Well, when you put the back cover on and screw it down make sure you have nothing touching the white wire leading to the oven light. I did and it blew the push switch when I threw the 220 breaker. Actually, the light was on when I came in the room, but when I pushed the switch on the front panel it sparked in the rear and popped the breaker. Then I saw the short and when I tested the switch it would not click. The install was fine.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Susan from HUDSON, MA
- Parts Used:
- 279570
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Pliers, Screw drivers
broken door catch
I followed your short video and found it very easy to do
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Frank from ENDICOTT, NY
- Parts Used:
- 279570
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Pliers, Screw drivers
broken door catch
Took 3 screws out used the putty knife to pry the door a part then used the pliers to remove the old door catch and then sapped the new one and put the door back together and I was was done in less than 10 min.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Michael from Goddard, KS
- Parts Used:
- 279570
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
broken door catch
the part fit perfectly, it just snaped right into place.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Melody from TEXARKANA, TX
- Parts Used:
- 279570
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Pliers, Screw drivers
Dryer door wouldn't catch and stay shut
I take the screws out of the door, I removed the catch from behind inside the dryer door, I slid the new catch in the door and snapped it in place. After getting a new catch in the door I put the door back together and put the screws in. Easy repair
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- william from KILLEEN, TX
- Parts Used:
- 279570
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Pliers, Screw drivers
door would stay closed
just replaced parys
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Shelley from Powell, WY
- Parts Used:
- 242905
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
I wanted a second 8" canning element for home canning
I purchased an 8" canning element for my new Kenmore Stove. The ordering process was easy. I printed my order out. I did not receive a confirmation by email, however I received the part in a timely manner. I was satisfied with the process.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- DONNA from SAN LORENZO, CA
- Parts Used:
- 279570
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
catch was missing to close dryer door
The only thing I had to do was hammer the catch inside the square fitting and presto it was done. It took me less than 3 mins. I thought I might of needed instructions, but it was really simple. Even a guy can do it. (smile)
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Gregg from St. Augustine, FL
- Parts Used:
- 279570
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Dryer door would not stay closed
After removing front door panel (2 screws) I removed the old latch catch and replace with the new part. 4 minutes later, the door was back together, the dryer was running and the door was staying closed.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Frank from Union Beach, NJ
- Parts Used:
- 279570
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
The door whould not close enough for the dryer to work.
Got my parts very quickly.
Popped out the old door latch with a screw driver and pressed in the new one.
Very simple.
Thanks Parts Select.
Popped out the old door latch with a screw driver and pressed in the new one.
Very simple.
Thanks Parts Select.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Diana from Canfield, OH
- Parts Used:
- 279570
- Difficulty Level:
- Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Pliers, Screw drivers, Wrench (Adjustable)
dryer door won't stay shut
I replaced the male end first hoping that a change in the female part would not be needed. Unfortunately no. I used needle nosed pliers to pry the male part out and pushed the new part in. The female part of the door catch was more difficult. I didn't do it in "textbook" form, but got the job done with pliers and a screwdriver. Worth every penny to fix correctly instead of rigging it. Do it!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Debra from Oakland, NJ
- Parts Used:
- 279570
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Pliers, Screw drivers
door latch broke
Pop out the old latch and replaced with a new one
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Rick from SAN DIEGO, CA
- Parts Used:
- 279570
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
latch was broke
just followed the video directions, worked perfectly thanks
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- j from TAZEWELL, TN
- Parts Used:
- 279570
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Pliers, Screw drivers
dryer would not run because catch did not hold tight enough to press door switch.
removed screws that held the door face to gain access to catch replaced catch reassembled door tried dryer works great!
Was this instruction helpful to you?
Thank you for voting!