Models
>
KUDI01FKSS1
KUDI01FKSS1 KitchenAid Dishwasher
Jump to:
Find Part by Name
Keep searches simple, eg. "belt" or "pump".
Diagrams for KUDI01FKSS1
Viewing 12 of 12
Keep searches simple, eg. "belt" or "pump".
$33.12
If your dishwasher door is not opening or closing properly, it may be time to install a new balance kit. This part helps to support the weight of the door as it opens and closes. You should also check...
In Stock
Order within the next 10 hrs and your part ships today!
The wheel mount for the upper rack of your dishwasher ensures that the top rack easily slides along the track when pulling it in and out. If a wheel or the mount becomes damaged, your top rack will no...
In Stock
Order within the next 10 hrs and your part ships today!
$7.71
This is a single rack track stop clip used to prevent the upper dish rack from sliding all the way out of the dishwasher. It is made of gray plastic and can wear with time. This is an easy repair that...
In Stock
Order within the next 10 hrs and your part ships today!
$10.04
The mounting bracket is used to secure the top part of your dishwasher to the underside of your counter or cabinet. If you have solid surface counters (granite, quartz, etc.) you will likely need to s...
In Stock
Order within the next 10 hrs and your part ships today!
If you are unable to smoothly roll the top dish rack of your dishwasher, you may need to replace some of the wheel assemblies. Over time they can become cracked and damaged, and once this happens, the...
In Stock
Order within the next 10 hrs and your part ships today!
$34.77
If your dishwasher is not cleaning your dishes properly, is not draining, or is noisy while operating, there may be an issue with your chopper assembly. The chopper is used to mince up food particles ...
In Stock
Order within the next 10 hrs and your part ships today!
$35.44
When replacing these fuses the wire harness must be replaced as well. It is located in the control panel. The harness is included with this part now.
In Stock
Order within the next 10 hrs and your part ships today!
$94.70
The door gasket provides a water tight seal, between the tub and the door, to keep water from leaking out of your dishwasher. If the dishwasher is leaking you may need to replace the door gasket. Thi...
In Stock
Order within the next 10 hrs and your part ships today!
$68.21
This water inlet valve should be located behind the lower kickplate panel in either the right or left corner. The attaching solenoid on the valve will open and close according to the desired amount of water needed.
In Stock
Order within the next 10 hrs and your part ships today!
$33.95
This dishwasher door spring is sold individually. It is recommended if you are replacing one side, to replace both.
In Stock
Order within the next 10 hrs and your part ships today!
In Stock
Order within the next 10 hrs and your part ships today!
This part releases the detergent and rinse aid into the dishwasher.
In Stock
Order within the next 10 hrs and your part ships today!
Questions and Answers
We're sorry, but our Q&A experts are temporarily unavailable.
Please check back later if you still haven't found the answer you need.
Common Problems and Symptoms for KUDI01FKSS1
Viewing 10 of 10Not cleaning dishes properly
Fixed by these parts
How to fix it
Leaking
Fixed by these parts
How to fix it
Door latch failure
Fixed by these parts
How to fix it
Will Not Start
Fixed by these parts
How to fix it
Noisy
Fixed by these parts
How to fix it
Door won’t close
Fixed by these parts
How to fix it
Not draining
Fixed by these parts
How to fix it
Not drying dishes properly
Fixed by these parts
How to fix it
Will not dispense detergent
Fixed by these parts
How to fix it
Will not fill with water
Fixed by these parts
How to fix it
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Scott from Fort Lauderdale, FL
- Parts Used:
- 8194001
- Difficulty Level:
- Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Replaced Hinge Link
Pulled dishwasher from under counter, attached link to spring, hooked spring back into frame/chassis, threaded link through pulleys, attached other end of link onto door, reinstalled dishwasher under counter. All's well. Note-I purchased an extra link anticipating that the other one will fail. They're cheap enough.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Jason from Todd, NC
- Parts Used:
- WP8268743
- Difficulty Level:
- Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Worn dishrack wheel mount
This wheel mount broke from normal use and made the upper dish rack disconnect from the sliding arm that extends it outside the dishwasher body so that you can fill it. The part was delivered quickly and was easy to install using just a screwdriver to loosen the retainer clip on the end of the extension slide. Once the retainer clip was r
... Read more
emoved, the new part was slid into place and clipped onto the rack. The install was complete.
Read less
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Elizabeth from San Francisco, CA
- Parts Used:
- WP8268743
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
The wheel mount had broken so that the wheel was disconnected from the mount on the upper rack, making the rack unstable.
I had to fiddle with the mount a bit to get it on the rack properly. Then I pulled back slightly on the inner part of the end piece of the track while also pulling the top of the piece back and released the inner tip of the piece, allowing the end piece to be removed. I placed the new wheel in the track and replaced the end piece.
... Read more
Super easy and a small fraction of what a repairman had told me the part would cost.
... Read more
Super easy and a small fraction of what a repairman had told me the part would cost.
Read less
Was this instruction helpful to you?
Thank you for voting!