KPDI620T6 KitchenAid Dishwasher - Instructions

Rubber Water Delivery Tube and Upper Spray Arm Receiver had worn out on my 24+ yr. old Kitchen Aid Dishwasher. First time anything every had had to be done to this machine. It has been a work horse and still works great. The above parts had simply worn out. I found this site online and sent for the parts. My husband replaced them and followed the instructions of greasing the parts when replacing them. The job was done in minutes and the washer is working fine again.

The parts were shipped promptly and we had them in a matter of two or three days. Great experience with this company and will use again if the need arises.

I pulled off the remains of the old tube and simply slipped the new hose on by hand. Easy as pie!

Pulled off old tube, applied small amount of lubricant to each end of tube, then just pushed ends together. Slide right on, attached new support and in less then five minutes, fixed. Dishwasher running like new.

removed old hose slid the new one on. Easy one minute job.

I removed clips on the end of the rack, removed the rack, and pulled old tube off. Used plain water as a lubricant to ease replacement of new tube on the dilated end. Very easy!

In my case the rubber tube was so worn that it came off very easily. I removed the tube, then with a little cooking oil, I lubricated the new hose and easily slipped it into place. Now my dishwasher works great! I ordered the part received it and repaired it for less than $20.00 and in less than 15 minutes.

Took old one off and put new one on, about a 4 minute job.
The part was about 1/3 of the cost if I had bought it local.

just popped the old hose off and put the new one on. the part was shipped very quickly and I received it within a week even during the holidays

For several years I endured difficulty in pushing in and pulling out a fully loaded lower dishwasher tray in my KitchenAid Superba dishwasher. The tray would "fall out" out of its "track" and jam requiring me to lift up the whole tray to try to pull it out. Then one of the plastic roller "axles" broke and its wheel fell off. So I went on to Part Select's website to find a replacement. When I got it in the mail I replaced the one that broke. I noticed how much more rigid the wheel then ran on its "track." So I replaced all the roller axles and, lo and behold, the lower tray does not jam anymore. It rolls just like new! I am very satisfied. Chris from Bay Ridge, Brooklyn

Took the tube off and noted that there was a factory drilled hole on the underside that lets water drain. I slipped the new tube over the inlet port and the other end over the rotating washing arm aparatus port and everything worked fine. Very easy and fast repair.

pulled off the old and put on the new. Great pictures on website so I got the right part the first time. Thanks!

It was 94 degrees that day so I set the rubber hose outside in the sun to loosen it up, make it more plyable. I then mixed up some soapy water and doused the ends of the hose with the soapy water and slid the hose right onto the fittings.

There was a small hole in the hose which was not discussed in the directions. I assumed the hole should be installed on the down side to let water drain out after the dishwasher is finished. This will reduce the chance of bacteria building in the hose.

I read the installation tips before I started and picked up the soap mix and heating up the hose before installation. Can be accomplished with a hair dryer if it is not 94+ degrees outside!!!

Thanks,

Jim

connected tube to spray arm and attached to back of dish wash machine.

I removed the broken axle with the help of a small screwdriver and replaced it with a new one. Then I installed a new roller, which was easy because all I had to do was push it on with my fingers.

One of the easiest repairs I've ever made on anything and now I'm happy because my wife is happy!

I had repaired the hose with duck tape several times, and finally was able to convince my husband to look up the model number etc. went on line to see if I could locate a dealer to get the hose, and that was so easy,
Ordered it, it came in 2 days, and my dishwasher works great again.

It was so easy just took off the old hose and snapped in the new one.