KUDB03CTBL0 KitchenAid Dishwasher - Instructions

Popped the old housing apart with screw driver, saving internal part, installed part into new housing, placed in posistion, installed two new screws and it worked like charmed. So simple, I have ordered 2nd part to replace opposite side which is not yet broken. Thanks to the terrific phone assistant who convinced me it would work and not have to replace the entire rack which was suggested by a repair man. . . . . . Many thanks! ! ! !

When the top rack stopped cleaning, I tracked down the problem to the food shredder/chopping blade, and then to the impeller that drives the blade. The knob on the impeller had sheared/broken off. That meant removing the motor, and replacing the impeller. Four hours, a band-aid, and a trip to Home Depot later, here are my suggestions

1. Look for videos – this site is awesome, but they don’t have a video on this particular repair. I found 4 that got me close to knowing what I was doing.
2. Do all the “remove internal stuff” - you had to anyway to find the issue with the shredder/cutting blade
3. Take pictures as you move along, you’ll need them when you have to remember the placement of the water line, drainage hose, wired connections etc.
4. You need a 1/4 inch socket set. A 3/8 drive will NOT work (it won’t fit between the shroud and the base). Don’t start working on the repair, unless you have a 1/4 in socket with about a 6" extension
5. Someone at Kitchenaid should be shot for having the waterline connection facing the back of the unit. Use a short adjustable wrench
6. The order comes with a washer, but when you take the impeller off this model, you’ll see you don’t need it.
7. Placement is everything – there was zero clearance between the bottom of the unit and the floor. Placement of the water line, drain hose, and power line was critical – had to re-position the unit about 7 times to get it to “play nice”.
8. Hindsight – only needed to remove the wire harness for the motor (take pictures)
9. Hindsight – gloves are a great idea – sheet metal is unforgiving

i asked the vrtual repair stating the problem of my dishwasher machine ,he then give me two possible solution change the water presure switch which i did order the part and installed it and it works now..............thanks partselect.

Disconnected Power, Turned off water valve, disconnected drain return line, disconnected water line, removed two screws on inside-top that was mounted to counter, pulled out dishwasher while feeding power cord, drain line, water line. Turned Dishwasher on it's side and disconnected water line and water fill line from Fill valve Assembly. Disconnected power connector from Valve. Removed one screw from Fill valve assembly and removed Fill valve assembly.
Installed Fill valve assembly and screwed screw back in. Installed Water line and water fill line from valve. Snapped power connector back in. Doubled checked Fill Valve connections to make sure they were tight. Slide Dishwasher back in while lines and power back through to under sink. Made sure Dishwasher was set in place and mounted two screws to counter. Connected water line to water valve and connected discharge line back to it's location. Turn water back on. Plug power back in.
Turned unit on and checked for leaks at the fill Valve assembly, water line and discharge tube.
Saved ~ $ 100.00. Easy job. I wished I didn't wait so long when it was making the noise for so long...Good luck..

pull out the dishwasher
lay it on its side
use a 1/4" drive socket with extension and a universal joint to undo the the hidden bolt,
twist the motor 1/4 turn. this is the hard part you have to pull fairly hard and rock the motor around a little to get the o-ring to let the motor slide out.
lube up the new motor with jet dry or soap and insert back it, turn it back 1/4 turn, install the bolt and plug the motor control wires back in, then reinstall it back under the counter

Removed old rack and and removed old rollers and installed old rollers on new rack as they work better than the new rollers sent with new rack

Grabbed old seal and removed it.(notice how seal was situated in slot)

Pushed new seal in slot that held old seal. close door.

If dishwasher still leaks you put the seal in backward (I did!)remove seal reverse it and reinsert it.

Just followed the YouTube video they sent with the receipt.

Since I had manual from initial installation I knew code meant heater was malfunctioning. Went to Sears, Lowes..no parts to repair. Instructed to go to appliance repair shop, closed of course...ordered online instead here and received in 2 days. Repair took 20 minutes. Super easy! Do not attempt to use adjustable wrench to tighten, use socket set as plastic electrode casings will be compromised. Takes some tork. Probably saved $100-$150 repair call. Wife was pleased. I was suprised how easy.

A Mouse friend had seen fit to chew through the original drain line. I used my Model Number, and was able to order the correct part . It arrived the next day. The job itself is fairly straight forward. You will need to access the rear of the machine. This may include shutting off, and disconnecting the water supply line. (Adjustable wrench). Mine is under the sink, on the "Hot" side. You may also need to un-plug the unit. (recommended) . A pair of (Pliers) will be needed for the spring clamp.

I removed the dishwasher from under the counter. This took the bulk of the repair time along with disconnecting the water supply and electrical connection. I had enough slack in drain hoses that I could turn the dishwasher over to replace the motor. I was surprised that there was only one bolt that held the motor in place. I put the motor on, turned the dishwasher upright and slide it back unde the counter and began the long process ofreconnecting everything. I am sureit could have gone faster if I were younger and did not need glasses for close work. Start to finish took me four hours. This was the fourth time I have replaced motors in dishwashers of various makes.

Removed the front panel of the dishwasher. Unhooked the electrical connection between the dishwasher and the dispenser, which was as easy as unplugging a cord from an electrical outlet. Removed the old dispenser and replaced it with the new one. Replaced the front panel. This was a super easy repair.

First research then troubleshoot
Removed
1 Upper rack
2 Lower rack
3 Lower Wash Arm and Strainer Parts
4 Upper Wash and Rinse Parts
5 Accumulator assy.
6 Motor shield
7 Inlet protector (most difficult)
Noticed blade was broken off chopper assy.
Replaced chopper assy.
Runs and cleans like new.
Most difficult step was to remove Inlet protector
After removing two torx screws (#15) used small pry bar to lift inlet protector from position. Not easy to accomplish with hands alone. Inlet protector fits tightly into position.

Disconnected power to dishwasher. Removed water supply hose from inlet water valve.
Removed lower and upper racks. Removed Lower spray arm. Removed tube from pump tp top spinner. Pulled dishwasher from under cabinet (remember to tip to get back out!). Placed dishwasher on its back. Removed electrical connectors from water valve, main motor and drain motor. Removed drain hose from drain pump. Removed pump/motor assy by pulling out wedges and pushing assembly into dishwasher. Removed pump/motor assy from inside dishwasher. Cleaned out pump. Installed new chopper. Re-install pump/motor assy. Re-install driain pump hose. Re-connect the pumps and water valve electric connectors. Slide dishwasher near cabinet for re-install. Re-connect drain hose to dishwasher. Re-install dishwasher under cabinet.Reconnect water supply. Removed top spinner from tube. Installed new spinner onto tube. Re-install tube onto main pump (below lower spray arm). Clean out and re-install lower spray arm. Remove middle spray arm from top rack. Clean out spray arm. Re-install spray arm with a new gasket (gasket may have not been needed). Re-installed lower and top racks. Re-connect power supply. Position all three spray arms pointing towards the door to confirm they were turning. Tested dishwasher - confirmed fill, wash, and drain properly. Also confirmed that all three spray arms were turning. Machine is washing, draining and running great since!

Looked at other side of top rack which still had the stop. Just had to orient the direction of the stop and push it firmly onto the rack arm. Took a couple tries, but it went in and locked. Works perfectly. Inexpensive and easy fix to to very annoying problem.