KUDB23HY0 KitchenAid Dishwasher - Instructions

Finally listened to advice of others online and decided to replace inlet valve. Btw, the problem is NOT the inlet screen. It was completely clean in my case. Issue is with internal seals that swell over time and restrict flow leading to low water level.

Unplugged unit, removed lower front panel (two screws on outside upper corners), undid compression fitting on inlet supply line, removed two screws holding valve bracket to frame, disconnected electrical connections to valve, used pliers to compress hose clamp to remove valve outlet hose, used adjustable wrench and some elbow grease to remove small inlet elbow (its on tight!) from valve inlet, put teflon tape on elbow threads to reinstall on new valve, reverse removal instructions to put everything back. All done! MUCH cleaner dishes!

I removed the old hose, I lightly coated the id of the new tube with vasoline, both ends, and then heated the oblong end with the hair dryer to soften it and it slid on with litte force. The round end installed without heating.

Loved how easy it was to deal with you!
Part was clearly pictured and came immediately!
Very satisfying to fix it so easily.
Wondered why we waited so long!

First I had to buy a new tray. I tried to remove the wheels from the old tray but they wouldn't come off without breaking. I ordered new wheels and axels and they went on fine with the aid of a C-clamp. Then I tried to remove the old bumpers but they broke when I tried to remove them.
So, I ordered two new bumpers. When I did I saw that another user had posted a note saying that the new bumpers slipped on well if heated in hot water first. So, I heated them in hot water and they slipped on easily and safely.

Took off old hose. It practically fell off.
Used a spoon to widen the ends of new hose and twisted on one end, then other end slipped on. Done!

Rubber Water Delivery Tube and Upper Spray Arm Receiver had worn out on my 24+ yr. old Kitchen Aid Dishwasher. First time anything every had had to be done to this machine. It has been a work horse and still works great. The above parts had simply worn out. I found this site online and sent for the parts. My husband replaced them and followed the instructions of greasing the parts when replacing them. The job was done in minutes and the washer is working fine again.

The parts were shipped promptly and we had them in a matter of two or three days. Great experience with this company and will use again if the need arises.

I pulled off the remains of the old tube and simply slipped the new hose on by hand. Easy as pie!

Everything worked perfectly---thanks to the suggestion of your call center agent. She suggested that since the replacement door handles were no longer available, I should consider repainting them--it worked like a charm. Please tell her she was a life saver. We rent that house in Fl and my returning tenants had complained about the discoloring refer handles. Thank you

Pulled off old tube and upper arm receiver.The new tube and the section it was to go on appeared to be too small. I heated new tube with hair blower and streched new tube so as to fit .

Removed bottom rack and replaced axles and wheels, works just like new and did it without any assistance from my son or Husband.

It was simple. I simply replaced the old water tube with the new one you sent, and it works like new. Piece of cake.

Removed old water tube and replaced it with the new one. Hard part was logistically trying to put it below the rack and it obviously it had to fit very tight and it was quite difficult to get in place, but I did it! Thanks to your easy to use website and excellent service. I was proud of myself for doing the whole job start to finish, and my husband was even more impressed. Only downside to that is that I think he'll be playing more golf, while I do the repair work from now on.

Took old one off and put new one on, about a 4 minute job.
The part was about 1/3 of the cost if I had bought it local.

Slipped old one off slid new one on . Took about one minute. Held well and is washing so much better now.

Repair was fairly easy, had to swith the mounting bracket from the old valve no problem. Install reconnected the water and the dishwasher works great now!