KUDS22HT0 KitchenAid Dishwasher - Instructions

I was trying to avoid having to buy a new dishwasher before the holidays. I went on YouTube and found the dirty dishes may mean bad water inlet valve. So, I used my meter to see if the valve was bad and sure enough it was. I ordered the part from Part Select. Once I received the part I removed the old one. Be sure to put a towel down to catch the excess water. The bracket that came with the new prt was a different configuration, but i swapped the new with old and it worked. I addition to the valve being bad the dishwasher upper and lower arms were somewhat clogged. I looked online again and followed YouTube instructions to clean. The dishwasher is cleaning like it is new. I would recommend to anyone doing work on their dishwasher to use part select and thoroughly clean the upper and lower arm.

Removed old tube.

New tube was a little tight, so I heated it with a hair dryer and used dish washing detergent - Joy - as a lubricant. Then the tube slipped on easily.

First the water tube arrived two days earlier than what I was expecting. I pulled the old tube off and slipped the new tube on by hand. The dishes in the top rack are now a lot cleaner than they have been for the past couple of months. In the future if I need repair parts this is where I will be coming to get them.

Very easily!! I am 19 years old and repaired the dishwasher for my grandmother in about 15 minutes. Great products.

just popped the old hose off and put the new one on. the part was shipped very quickly and I received it within a week even during the holidays

Removed old tube, moistened both ends of new tube with hot water and slid over inlet and outlet holes. Repair done!

First I pulled off the tube that was hanging down and obstructing the rotation of the top spinner. Then I just reinserted the new tube. I'm a "do it your selfer" and I usually fix things by my self. But the few times that I've failed lived forever in my wife's memory. She dreaded my fooling with a machine that had outlived it's life. I promised that the job would only take about five minutes. She heard this before and resigned herself to having parts all over the kitchen floor and a full day of catastrophe. There is nothing like a satisfied wife.Thanks to You and your Staff, I have now regained my rightful place as her trusted HERO.. ,

I removed clips on the end of the rack, removed the rack, and pulled old tube off. Used plain water as a lubricant to ease replacement of new tube on the dilated end. Very easy!

For several years I endured difficulty in pushing in and pulling out a fully loaded lower dishwasher tray in my KitchenAid Superba dishwasher. The tray would "fall out" out of its "track" and jam requiring me to lift up the whole tray to try to pull it out. Then one of the plastic roller "axles" broke and its wheel fell off. So I went on to Part Select's website to find a replacement. When I got it in the mail I replaced the one that broke. I noticed how much more rigid the wheel then ran on its "track." So I replaced all the roller axles and, lo and behold, the lower tray does not jam anymore. It rolls just like new! I am very satisfied. Chris from Bay Ridge, Brooklyn

Took the tube off and noted that there was a factory drilled hole on the underside that lets water drain. I slipped the new tube over the inlet port and the other end over the rotating washing arm aparatus port and everything worked fine. Very easy and fast repair.

One of the axles broke off, requiring no removal. The other wheel broke off, but the axle remained. That required squeezing (pliers) to push out. Replacement was easy; just put wheel onto axle and push axle through mounting space. Total: 5 minute job.

Took the old one off then used canola oil to put on the inside of the tube and it went on easy.

I removed the old tube--I had taped over the hole. I didn't quite have the hand strength to fit over the ends and push the new tube into place. So, my husband did that at both ends without a problem. I'm relying on PartSelect for when I need parts for my 13 year-old appliances.

Replaced the tube. It was relatively easy although it did take a small bit of squeezing/reshaping the newer rubber tubing to get it to fit on the outlet (it was a bit snug.)

screwed it in. Closed the door. Voila, it works!