KUDC10FBWH0 KitchenAid Dishwasher - Instructions

FIRST I TURNED OFF THE POWER GOING TO THE MACHINE!!!! Then I removed the top rack by removing the (2) end caps on the front of the rack glides first then lifting the rack upwards and out. Next I removed the bottom rack which slid out easily. I then removed the lower spray arm that was held in place by the plastic turn-screw portion of the lower spray arm support/hub. I turned the screw a few times and the spray arm was released. I then released the feed tube assembly that was held in place by (2) clips; one clip was on the back panel of the tub (above the probe area) and the other clip was on the top panel of the tub (before the upper arm spray). Then I turned the entire tube feed assembly a quarter turn to the right so that it was possible to separate/unsnap it from the feed cap on the bottom. After the feed tube was moved away I was able to access all (4) screws that holds the accumulator in place. I used an allen wrench to remove those. After the accumulator was removed I saw two screws that was holding the 2-part protective cover of the chopper assembly. The small cover came out easily, the round cover took a little jiggling and fussing until I figured out how to pop it out. The chopper was revealed when the cover came off and I found it to be very warn and a bit bent. I pulled it out by pulling it upwards and forward towards me. At this time I also removed the valve check. To my surprise it didn't look like the one that I bougth to replace it. It was missing the round disk portion. I fished around thinking it may have somehow fallen off, but I didn't find anything. I put the new one in, disk-side down. I then put the chopper assembly in place and put everything back together again. I'm not 100% sure that it is completely back to normal. It seems to leave significantly less debris than before, but I noticed that there is more water on the bottom of the basin now. So it may not have been my only problem. If anyone has experienced the same thing I would really like to know

Removed new from box and installed rollers as instructed that's all there was , very easy.

Watched the video, it went as advertised. Easy repair and the noise is gone.

all 4 wheel units needed to be replaced, popped them off and installed need wheel units in roughly 10 minutes, no tools needed.

You need to pull the unit out to get access to the spring connected to the rear leg frame. Use the everything in the kit. The rollers are upgraded and will guid the cable better.

When the top rack stopped cleaning, I tracked down the problem to the food shredder/chopping blade, and then to the impeller that drives the blade. The knob on the impeller had sheared/broken off. That meant removing the motor, and replacing the impeller. Four hours, a band-aid, and a trip to Home Depot later, here are my suggestions

1. Look for videos – this site is awesome, but they don’t have a video on this particular repair. I found 4 that got me close to knowing what I was doing.
2. Do all the “remove internal stuff” - you had to anyway to find the issue with the shredder/cutting blade
3. Take pictures as you move along, you’ll need them when you have to remember the placement of the water line, drainage hose, wired connections etc.
4. You need a 1/4 inch socket set. A 3/8 drive will NOT work (it won’t fit between the shroud and the base). Don’t start working on the repair, unless you have a 1/4 in socket with about a 6" extension
5. Someone at Kitchenaid should be shot for having the waterline connection facing the back of the unit. Use a short adjustable wrench
6. The order comes with a washer, but when you take the impeller off this model, you’ll see you don’t need it.
7. Placement is everything – there was zero clearance between the bottom of the unit and the floor. Placement of the water line, drain hose, and power line was critical – had to re-position the unit about 7 times to get it to “play nice”.
8. Hindsight – only needed to remove the wire harness for the motor (take pictures)
9. Hindsight – gloves are a great idea – sheet metal is unforgiving

pull out the dishwasher
lay it on its side
use a 1/4" drive socket with extension and a universal joint to undo the the hidden bolt,
twist the motor 1/4 turn. this is the hard part you have to pull fairly hard and rock the motor around a little to get the o-ring to let the motor slide out.
lube up the new motor with jet dry or soap and insert back it, turn it back 1/4 turn, install the bolt and plug the motor control wires back in, then reinstall it back under the counter

Removed old rack and and removed old rollers and installed old rollers on new rack as they work better than the new rollers sent with new rack

Just followed the YouTube video they sent with the receipt.

watched instructions and proceeded. Parts were self evident after watch ing video. Easy replacement.

A Mouse friend had seen fit to chew through the original drain line. I used my Model Number, and was able to order the correct part . It arrived the next day. The job itself is fairly straight forward. You will need to access the rear of the machine. This may include shutting off, and disconnecting the water supply line. (Adjustable wrench). Mine is under the sink, on the "Hot" side. You may also need to un-plug the unit. (recommended) . A pair of (Pliers) will be needed for the spring clamp.

I removed the dishwasher from under the counter. This took the bulk of the repair time along with disconnecting the water supply and electrical connection. I had enough slack in drain hoses that I could turn the dishwasher over to replace the motor. I was surprised that there was only one bolt that held the motor in place. I put the motor on, turned the dishwasher upright and slide it back unde the counter and began the long process ofreconnecting everything. I am sureit could have gone faster if I were younger and did not need glasses for close work. Start to finish took me four hours. This was the fourth time I have replaced motors in dishwashers of various makes.

The replacement kit came with no instructions in the box, so I found the instructional video online. This video pointed me in the right direction so I could take it the rest of the way myself.

Here is the link to the instructional video i used
https://www.partselect.com/PS10065979-Whirlpool-W10712395-Upper-Rack-Adjuster-Kit-White-Wheels-Left-and-Right-Sides.htm

Even though I purchased the end cap pieces for the roller stops, I was able to reuse the original pieces so these are to be keep for spare if required.

This was a very cost effective repair instead of replacing the entire rack assembly.

NOTE: The original Wheel bracket was a molded plastic piece, but the replacement is Stainless Steel. This had no impact on the functionality, but did add a small amount of noise during the wash cycle. My belief is this is the water hitting the steel vs. hitting the plastic.

First research then troubleshoot
Removed
1 Upper rack
2 Lower rack
3 Lower Wash Arm and Strainer Parts
4 Upper Wash and Rinse Parts
5 Accumulator assy.
6 Motor shield
7 Inlet protector (most difficult)
Noticed blade was broken off chopper assy.
Replaced chopper assy.
Runs and cleans like new.
Most difficult step was to remove Inlet protector
After removing two torx screws (#15) used small pry bar to lift inlet protector from position. Not easy to accomplish with hands alone. Inlet protector fits tightly into position.

What I needed were simple clips to lock in the wheels. I ended up getting a kit that required replacement of the roller tracts on both sides of the upper rack. The instructions were terrible. The repair took far more time than it should have. Once one side was fixed it was easy to fix the other side. By then I had worked my way around the muddled instructions.