KUDS30SXBL3 KitchenAid Dishwasher - Instructions

I simply had to hook up the power cord to the dishwasher so i could plug it into the outlet rather than direct wire the appliance. Everything went very smoothly. Everything needed for installation other than tools was provided. Easy to follow instructions if you know a little about electrical wiring.

Pulled off old seal found center of new seal and pushed new seal into channel that old seal came out of starting at top middle underneath the latch

watched video took less than 5 min to replace veeeery easy to do

Followed the easy how-to video from PS. It was as easy as changing a light bulb.

Just followed the YouTube video they sent with the receipt.

First, I bought the door balance link to replace the broken links that connect to the springs.

Because I didn't have enough slack to simply pull out the dishwasher far enough to reach the springs, I had to disconnect the water line and electrical wiring.
The only reason my repair took as long as it did was because there was so little room underneath the dishwasher for disconnecting the water line. I had to buy a shorter adjustable wrench. Also, I had leaks after reconnecting the water line. I had to tighten the compression nut as far as it would go. The nut wrapped around a white substance that had been applied to the threads (I believe this is called pipe tape), which did the trick for sealing the leak.

The repair was a complete success! The parts arrived fast and the information from other customers on the the PartsSelect website was invaluable.

Removed the old hose, after loosing metal looking rings. Installed new hose ad finally tight firmly the looking rings, using wrench and socket.

I Removed the upper wash rack by removing locks on each front slide of rack. I laid a towel in the bottom of the washer to keep anything dropped, retrievable. I then removed the top screw closest to the spinner location. I then carefully pulled down on the mounting, which exposed the bad bushing lock. I removed the old bushing lock and replaced with new one. I then replaced the spinner with a push with one hand while holding the bushing in place with the other hand. You will feel a snap as all goes into place. Make sure new spinner spins freely. Now reinstall removed screw. Do not over tighten. Now reinstall lower rack, carefully aligning water feed in rear of washer, and making sure all rollers are back in sliding rack. Reinstall locking tabs onto sliding rack. Now slide out rack, it should not come off slider. Important: now remove the towel in the bottom of the washer. If left in place, you will have a fire during the drying cycle. Close the door and test your washer through a cycle. I felt confident and did a load of dishes. If all went well, spinner should be in place, not in the bottom of the washer.

Watch your video about my dishwasher symptoms. Move water tube for upper rack to the right and release lower spray arm. Remove 4 clutch head screws from filter cover and remove. Dig out 10 years of undisolved soap and reassemble.

Pulled upper tray out. Removed old adjusters and replaced with new. The pictures in the installation instructions were bad (blurry and hard to distinguish). Had problems with the first side button. Put it in before installing the wheel base on the second side. Went much easier that way. You did need a star tip for the screws.

I opened the package took out the replacement part and installed it with no tools. Easy, done in 10 minutes.

Looked on you-tube and it was so easy. Pump on bottom right. unplug pump and do a halfway turn. Plug the new one up and place the pump on, and turn halfway and its on. START your dishwasher

I followed the instructions on your recommended video; so easy! Thank you!

thought it could be due to the overfill control switch,so ordered one and replaced one in the washer. However, it did not solve the problem. Having a repair company coming to look at the dishwasher. Tipped the washer on its back and switch was readily accessable. Only had to open plastic covering over the switch, disconnect the wires and install new switch and reconnect the wires.

Hardest part was pulling dishwasher away from cabinet, making sure to not disturb water and drain line. I replaced both door springs which are on the two sides and attached to the dishwasher frame towards the back. This necessiatated pulling the dishwasher about 2/3 out of cabinet. After attaching both springs to frame, replacing the balance kit was a breeze .One screw to remove and then replace with new pulley unit. Attach the supplied cord with attached fittings to spring and then around two pulleys and mounting point on frame. Done . Push dishwasher back into cabinet, reattach two screws to underside of counter. Probably did not require new springs as they seem heavy duty and were not broken upon examination but ordered them also and replaced just in case. Most problem would be with broken cord in balance link kit