KUDC10FBBL0 KitchenAid Dishwasher - Instructions

Follow directions

The upper spinner was laying in the top washer basket. I went online but no help was avaiable. Went to store where we purchased dishwasher and they gave me part number to order but not online I had to call to order. Part arrived in about three days. I took two screws loose on the top of dishwasher removed broke retainer to put new retainer in but I drop it into dishwasher so you have to me very careful
so I tried to order just the retainer but is not sold by it self. Had to order whole new kit. Other than that it is easy dishwasher runs like a new one.

Just snapped it right into place! No tools required. Very easy!

Replace motor/pump assembly

I removed the old gasket. Cleaned the surface under the old gasket and began pressing the new gasket into place. Make sure the gasket is pressed all the way in to properly seat it in the groove. Didn't use the tube of gasket sealer and it worked perfectly no leak,

Was a cinch just watched the video whole procedure took an hr or so

1.Check the lines for any obstruction. Gunk can easily build up. I have used the dishwasher for approx. 10 years. I do rinse/scrap dishes prior to loading.
2. Drain all remaining water.
3. Unplug the dishwasher.
4. Grab a towel and proper screw driver. Unscrew the bottom protective plate. Remove the insulation plate.
5. The drain pump is located to the bottom left. Have your towel under it. Unplug it gently. Turn counter clockwise to remove.
6. Install the new drain pump (reverse order)
7. Return the insulation plate. Screw back the bottom protective plate.
8. Plug in

I followed the PartSelect video to replace the feed tube assembly with spinner and the spray arm seal for the middle wash arm. Washing performance was better, but a couple weeks later the dishes on the bottom rack suddenly stopped getting clean. I decided I probably needed a new chopper assembly, which is identified by PartSelect as the cause of problem for 48% of the cases of dishes not getting clean. Before ordering the chopper assembly, however, I followed the video about how to replace the chopper assembly to determine whether the chopper assembly seemed to be worn out (the video shown at https://www.partselect.com/PS11722146-Whirlpool-W10083957V-Chopper-Assembly.htm). It was worse than I anticipated. I found the holes of the chopper assembly screen blocked by food, and the spinner in front of the screen had broken apart. In addition to finding the pieces of the broken chopper assembly, I discovered a treasure chest of debris, including about 8 pieces of broken glassware, 3 twister ties, a half-inch button, a 3/4-inch screw, and dozens of small pieces of metal. I poured water into the area and used a kitchen baster to suck out the water with all the pieces of debris, finishing the clean-up with paper towels. I ordered a new chopper assembly to replace the broken one, and the part arrived in under 48 hours. I relied on the same video to install the new chopper assembly. The only tricky challenge was getting the new chopper assembly back into place. I first tried needle nose pliers in two sizes, as recommended in the video, but what worked much better for me was using two chop sticks that were each about 1/4 inch square from top to bottom. Needle nose pliers are slanted, but the chopsticks did not vary in thickness and separated the screen from the spinner an even distance apart, making it easier to get the gear shaft on the chopper assembly to align in a straight line with the gear shaft on the pump motor. I also rotated the two gear shafts so the gears of the chopper assembly would mesh correctly with the gears of the pump motor shaft. The video cannot show that step very well because the man's hand blocks vision of how exactly to fit the chopper assembly into place. The video also fails to warn about possible debris around the chopper assembly and to explain how to clean out the debris. After finishing installing the chopper assembly my 14-year-old dishwasher cleaned my dishes as well as a new dishwasher. I spent a total of $110.24 on parts and shipping and invested a couple of hours total. The alternative would have been to spend $800 on a new dishwasher or wash dishes by hand. I am very, very happy with the outcome.

I found instructions on line when I goggled my dishwasher name and model number with the words noisy door. There were three or four good suggestions at a couple of the sites I visited. I tried applying vasoline, then silicone to the rope where it travels through the plastic guides but that just cut the sound down about 50%. My dishwasher has plastic guides that look like rollers but they don't turn, they are fixed in place. The ropes squeak as the pass over the guides. The replacement part kit has plastic guides that turn like wheels now so the rope does not drag over them and squeak. This repair could be done by me in 20 minutes or less every time now that I know what I am doing.

I removed the black bottom metal cover then turned the nuts on the adjusting (leveling) bolts to lower the front end of the dishwasher so I could pull it out of the cabinet. Once I lowered is as low as it would go I opened the door and pushed down on it which tilts the dishwasher down and you pull out on it and the top lip clears the cabinet. If your dishwasher just pulls out the first time you try these steps may not be necessary.
Once the dishwasher is out the guides and rope are down at the bottom in the front by the door. It's obvious what to do to replace them.

Remove upper tray and spray arm. Remove two screws retaining pipe for upper spray arm and overhead. Unscrew retainer on top of lower spray arm and remove. Gently rotate the upper feed pipe clockwise until pipe can be removed from lower pipe. You may then remove the lower pipe and bearing housing where the seal is. Reverse order for reassembly. I also replaced upper spray arm bushing. Very simple, remove one screw and the arm will come out.

I followed the directions on YouTube and the paper that came with the part. The only problem is the 'little tabs' that they act like are easily pushed are rather more difficult since you don't want to break the things off.

The repair was really easy. First disconnected electricity staring with fuses and removing wires from dishwasher, then disconnected drain hose and water hose. Pulled it out and removed pump turning clockwise no need for tools and same way installed new one. Very easy

Pulled everything out the front, and dug down to find a thrashed chopper assembly (like a little garbage disposal). The previous owner just tossed anything in; pop tops, plastic cutlery, etc.
Didn't pay attention to the exact installation of the chopper as I pulled it out, but, it turns out that it only goes in one way.
Used pictures and instructions I found online as a guide and didn't have any issues.
Replaced the check valve because it isn't expensive and I was in the neighborhood.

Although the lower rack was a slightly different style than our original, it fit the dishwasher perfectly. We needed to transfer the silverware racks to the new rack and insert one set of removable tines. About 5 minutes and we are very happy with the repair.

followed video instruction