KUDS30CXBL6 KitchenAid Dishwasher - Instructions

The upper spinner was laying in the top washer basket. I went online but no help was avaiable. Went to store where we purchased dishwasher and they gave me part number to order but not online I had to call to order. Part arrived in about three days. I took two screws loose on the top of dishwasher removed broke retainer to put new retainer in but I drop it into dishwasher so you have to me very careful
so I tried to order just the retainer but is not sold by it self. Had to order whole new kit. Other than that it is easy dishwasher runs like a new one.

Just snapped it right into place! No tools required. Very easy!

I removed the old gasket. Cleaned the surface under the old gasket and began pressing the new gasket into place. Make sure the gasket is pressed all the way in to properly seat it in the groove. Didn't use the tube of gasket sealer and it worked perfectly no leak,

Replace motor/pump assembly

Was a cinch just watched the video whole procedure took an hr or so

The repair was really easy. First disconnected electricity staring with fuses and removing wires from dishwasher, then disconnected drain hose and water hose. Pulled it out and removed pump turning clockwise no need for tools and same way installed new one. Very easy

Pulled everything out the front, and dug down to find a thrashed chopper assembly (like a little garbage disposal). The previous owner just tossed anything in; pop tops, plastic cutlery, etc.
Didn't pay attention to the exact installation of the chopper as I pulled it out, but, it turns out that it only goes in one way.
Used pictures and instructions I found online as a guide and didn't have any issues.
Replaced the check valve because it isn't expensive and I was in the neighborhood.

followed video instruction

Although the lower rack was a slightly different style than our original, it fit the dishwasher perfectly. We needed to transfer the silverware racks to the new rack and insert one set of removable tines. About 5 minutes and we are very happy with the repair.

I found instructions on line when I goggled my dishwasher name and model number with the words noisy door. There were three or four good suggestions at a couple of the sites I visited. I tried applying vasoline, then silicone to the rope where it travels through the plastic guides but that just cut the sound down about 50%. My dishwasher has plastic guides that look like rollers but they don't turn, they are fixed in place. The ropes squeak as the pass over the guides. The replacement part kit has plastic guides that turn like wheels now so the rope does not drag over them and squeak. This repair could be done by me in 20 minutes or less every time now that I know what I am doing.

I removed the black bottom metal cover then turned the nuts on the adjusting (leveling) bolts to lower the front end of the dishwasher so I could pull it out of the cabinet. Once I lowered is as low as it would go I opened the door and pushed down on it which tilts the dishwasher down and you pull out on it and the top lip clears the cabinet. If your dishwasher just pulls out the first time you try these steps may not be necessary.
Once the dishwasher is out the guides and rope are down at the bottom in the front by the door. It's obvious what to do to replace them.

Remove upper tray and spray arm. Remove two screws retaining pipe for upper spray arm and overhead. Unscrew retainer on top of lower spray arm and remove. Gently rotate the upper feed pipe clockwise until pipe can be removed from lower pipe. You may then remove the lower pipe and bearing housing where the seal is. Reverse order for reassembly. I also replaced upper spray arm bushing. Very simple, remove one screw and the arm will come out.

1.Check the lines for any obstruction. Gunk can easily build up. I have used the dishwasher for approx. 10 years. I do rinse/scrap dishes prior to loading.
2. Drain all remaining water.
3. Unplug the dishwasher.
4. Grab a towel and proper screw driver. Unscrew the bottom protective plate. Remove the insulation plate.
5. The drain pump is located to the bottom left. Have your towel under it. Unplug it gently. Turn counter clockwise to remove.
6. Install the new drain pump (reverse order)
7. Return the insulation plate. Screw back the bottom protective plate.
8. Plug in

1) Remove the racks

2) Unattach the feed tube the runs from the bottom of the dishwasher tub along the back to the top (this is the grey plastic tube that the top rack sprayer plugs into). This is done by unclipping the tube in two places, one stainless clip is in the back of the tub and one stainless clip is on the top of the tub.

3) After the tube is loosened from the clips, give the tube a 45° twist clockwise (relative to the bottom of the tub) and then pull up. This should remove the entire feed tube and bottom sprayer assembly.

4) There are now 4 stainless steel torx screws visible on the bottom of the tube. Remove the screws using a torx driver. Remove the grey plastic "gear looking" piece that was held in by the screws by pulling straight up.

5) On the left hand side of the tub you will see one more (smaller) torx screw. Remove this screw and then with a pair of plyers, give the housing piece that was held on with the screw a tug straight upwards. There is a post sticking straight up that will help you do this.

6) The grinder assembly is now visible, and in my case, completely jammed with paper. Pull the grinder and screen out of the groove it is sitting in.

7) Place the new grinding and screen into the groove. The grinder blade will have to be pull back (toward you) so the grinder coupling teeth can properly engage with the motor coupling teeth. This may take some fiddling.

8) once the grinder is installed, reverse all the steps starting at step 5.

simple...a female did it!! Dealing with PartSelect was so easy...your was the only web site that made it super easy to find my part. Placed order and paid for it...part arrived the next day!! Sent web site link to hubby too. When we need parts again for any applicance in our home, we will check your site out first!!

Very easy to repair with the replacement wheel assembly. Popped out the broken one, popped in the new one. Price was nothing compared to having an professional repair person come to the home. Glad I found you on line!