KUDM220T3 KitchenAid Dishwasher - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Mark from Norman, OK
- Parts Used:
- WP4162568
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
Detergent dispenser failed to open
Removed the door cover and replaced the bi-metal.
Was this instruction helpful to you?
Thank you for voting!
Old float stem had fine thread new one had corse and did not supply nut so had to use old one over.
put new switch and new gasket on old float stem with old nut. but it still overflows about 1/2 cup of water through stem
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Albert from Highland, TX
- Parts Used:
- 4169400
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver, Screw drivers
Replaced black panels with stainless.
Just followed directions included.Am extremely pleased with the appearance of the new panels they matched my new appliances.Also I did not pay for express freight but received my order in only two days.Very pleased with Part Select.Thanks Al S
Was this instruction helpful to you?
Thank you for voting!
Roller Wheel on lower dish rack broke- rack didn't sit or roll properly.
used screwdriver to remove roller axle. Snapped on new axle and wheel. I ordered two extra sets just in case future wheels brake. simple. 16 Year old dishwasher works fine!!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Eddy from Greenville, CA
- Parts Used:
- 4169400
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver, Screw drivers
no problem---color change
unscrewed 4 screws on top panel and 2 on bottom panel... real easy fix.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- David from Carlisle, PA
- Parts Used:
- WP4162568
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Pliers, Screw drivers
Soap Cup Lid was not opening during main wash cycle
Very easy. Disconnect power to the dishwasher via a breaker or fuse. Open the door and remove just the 4 screws on the inside lip of the door. Do not remove the screws hoding the closing brackets. Remove the front glass and chrome panel between the control panel and the kick panel. This will give you access to the soap cup and bi-metal. Remove the one retaining screw and remove the bi-metal,taking note of the position of the wires. Remove the wires, by grasping the connectors (I used needle nose pliers for this), not the wires, and re-intsall them on the new bi-metal. Re-install bi-metal on soap cup assembly, "cock" the release lever by closing the soap cup cover and manually trip the bi-metal to make sure it will release the lever and open the cover. Re-install the front panel with screws. Restore power and test appliance.
Was this instruction helpful to you?
Thank you for voting!
A few rollers and axels had gone missing
Easily one of the easiest repairs I have ever done. The new bits snapped into place and now the bottom rack rolls in and out like brand new.The ease and speed of finding the parts was really helpful. This is an old model and to be able to find the exact parts I needed so fast and so cheap was great. Oh and they arrived the day after I ordered them! Insanely fast!
Was this instruction helpful to you?
Thank you for voting!
bottom tray had come off
I took off all the old axils and put new ones on,and then I slide the wheels on and That was all is to it. EASY!!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- sarah from MELBOURNE, FL
- Parts Used:
- 4162321
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
the plastic roller axles had become brittle, and were breaking, dislodging the little wheels that guide the lower rack in and out of the unit smoothly
broke off the remaining roller axles, pushed the new roller axles into place, then snapped the little wheels onto new axles. I FELT LIKE WONDER-WOMAN, FIXING MY OWN DISHWASHER!!!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Jack from Scarsdale, NY
- Parts Used:
- 4162655
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Upper rack conduit tube came loose and melted on the heating coil
Simple replacement with new part
Was this instruction helpful to you?
Thank you for voting!
wheels on bottom drawer broken
Took out drawer. Replaced broken/missing wheels and axles. Used pliers to snap them together.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- David from St. Marys, KS
- Parts Used:
- 4162321
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- Less than 15 mins
4 pcs broken & would not hold wheel on Basket.
Push off - Push on new plastic Part. Very stiff. Used a wooden spoon handle!!! Job done!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Donald A from Los Angeles, CA
- Parts Used:
- WP4171000
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 1- 2 hours
- Tools:
- Pliers, Screw drivers, Wrench (Adjustable), Wrench set
Water wouldn't activate when button pushed to activate
The previous pump needed to be removed, install new. New pump mounting bracket hit existing mounting bracket from an adjacent part. 1. Wire contacts removed 2. Copper incoming line was disconnected from brass elbow. 3. Hose to pump removed using pliers for wire clamp, and flat head screw driver to prod hose off. The used pump is now in one's hand. The new pump would not fit using existing screw holes. The mounting bracket was moved to the left, using the one pre-existing hole and right hole in mounting bracket. The left hole of the mounting bracket was used as location for another hole to be bored/drilled out. Two drill bits of different sizes were used, along with the same sheet metal screw which was in previous mounting bracket assembly. Pump design has been changed from two wire coils to one wire coil. 1. The hose was re-connected using pliers. 2. Copper compression fitting lined up with brass elbow again. 3. Two Wire contacts were attached; previously there were Three contacts. 4. Second screw was added in newly bored hole. Plenty of room moving to the left. There is one loose wire contact.
Was this instruction helpful to you?
Thank you for voting!