KUDE20IXWH3 KitchenAid Dishwasher - Instructions

After unscrewing the dishwasher, I pulled out the washer, I saw that the springs were attached just by strings that were broken... I just used the strings from an old lanyard, retied everything, and did not need the springs! works well!

First, I replaced the bottom door seal. You will need magnetic nut drivers because of the location of the 3/16 screws that hold the seal in place. you also need a 1/4 in nut driver to remove plastic cover that covers up the 5 3/16 screws. Last you need a small star driver to remove the door screws. Note 4 of the door screws, the 4 on top of the door are much longer than the side screws. With all this said, this seal was not my problem. I then replaced the large black rubber seal around the tub. Be sure if you do this you fold the seal in half and start in the middle of the top of the opening so you have the exact amount of seal left over on both sides. Also when you remove the old seal, clean the area it was removed from with a damp cloth. Turns out, That was not my problem either. So now I will move to the next step to see where the water is coming from but maybe this information will help someone with a simple door leak.

I took a picture of the old assemblies position. Then I removed one side. It was original and held in place by plastic snaps. We followed the instructions on the first side. The metal wheel assembly and the housing have matching channel & grove so the metal fits into the channel on the housing. We accidentally placed the metal wheel assembly in the adjustment housing backwards then could not get it out and broke two small plastic tabs getting it back out. Turns out that was not a fatal error. We had a bit of difficulty determining the exact positioning of the actuator in the housing and how the housing fit to the rack. One has to really look hard at the instructions. !!!A YouTube video would be very nice for this!!! Once we had the positioning then the assembly went together very easily. The two screws went in easily with a ratchet nut driver and star bit. (an adapter is provided for those who don't have the star bit). The second side was incredibly easy since I knew exactly how to put it together the second time. First side: 20-25 min. Second side 5 min.

This product comes in a bottle with a brush like Liquid Paper. It goes on incredibly easy. A second coat might be needed. I wanted to prevent rust from setting in so I covered the scratches and dings. The paint is a little brighter since my washer is 10 years old but it still looks great.

1. Disconnect power at the breaker, 2. remove two wood screws fastening the dishwasher to the cabinet and slide the unit out approximately 2 inches. 3. Remove old latch strike and replace with redesigned strike. 4. Slide unit in and reattached to cabinet. 5. Remove 11 screws holding inner panel of door assembly and one screw holding user interface unit to door. 6. Disconnect snap cable to latch assembly and replace the latch unit. 7. Reassemble.

Popped out old wheel housing. Popped in replacement with a little help from a flathead screwdriver. Easy.

Simply snap the old one off and snap the new one on. Simple as that less than 15 seconds.

Pulled dishwasher out from under counter. Relaced cord with plastic hook attaching spring to door. Very easy.

Very impressed with Partselect.com. Full schematic of dishwasher made it easy to select part.

Delivered in 1 day. Fantastic. Highly recommend

Put thread tape on threads. Screwed water hose to part. Pushed hose onto part. Pushed electric clip to part. Screwed part onto washer. Done

Per the you tube video

Removed old parts by breaking them with a screwdriver. Insert thr stainless slide. As shown by twisting thought through wire rack the rest is easy.

The left side took 20 minutes the right side took 3 minutes. The instructions do not describe how to remove the old assembly but rather just assume you have already done it. It takes one minute to see how the six parts fit together and then you just have to begin disassembling the easiest piece. The final cover removal required a flat head to pry apart two pieces held together in a pressure fit with round tabs locking them in. I was worried about breaking a piece in case the new parts didn't fit properly and I would have to reinstall the old pieces temporarily but you just have to keep the faith and open it up for final removal. Installing the new parts was simple however it would be nice if the images on the instructions were of better quality. The result was perfect and the kit feels more robust than the original parts. There is nothing here an average person can't do with a screwdriver and a little patience.

Removed old tracks. Note instructions do not tell you to remove the back stops one each side.... let alone how. Installing new track is really easy. Place the old lock on the track. Strange they don't arrive with a new lock, it is just a plastic insert and must be cheap. The only tricky part is replacing the rack wheels and height adjuster. If the instructions and particularly the pictures in these, were better it would all have been a breeze. Really worth the effort though!

It was very easy to pry off the old wheel assemblies with a screwdriver and pop the new ones in place. Although the part is called "wheel" it is actually the plastic piece containing two wheels. I thought it was a little confusing to just call it "wheel" as each piece has two wheels. It was an easy repair.

Followed a video, pretty straightforward. Be sure to clean all the area. My husband used cotton swabs to clean all the gunk.