KUDS40CVSS2 KitchenAid Dishwasher - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Richard from Ann Arbor, MI
- Parts Used:
- WP8535660
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
The old seal would often travel with the door when opened.
I removed the old seal and carefully cleaned the track into which the seal was fixed. No tools other than some ordinary cleaning liquid, cloth and small wooden piece to swab out the track. Easy and quick. As a note here, I first used the incorrect schematic for the unit and ordered the wrong seal. However after receiving the wrong part, I made the correction and reordered. I did this over the phone as I needed instructions to return the part. The person taking my order and answering my questions was very helpful and I want to take this opportunity to thank her.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Martin from Discovery Bay, CA
- Parts Used:
- 8194001
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
The door spring link broke.
Unplug dishwasher and slide it out from under cabinet. Remove old broken link (a heavy string between two plastic parts) and replace with new one. Slide dishwasher back and plug it in. Very easy and no tools required.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Joan from Rockville, MD
- Parts Used:
- W10728160
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
The cap of a vertical tine in the dishwasher had come off, leaving an exposed, rusted and sharp top.
The old tine row came out easily and the new one was easy to pop into place. I was pleased that it was so easy to order a replacement part.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Thomas from WEST WARWICK, RI
- Parts Used:
- WPW10348269
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Dishwasher would not drain. Pump was jammed with broken glass .
Turn off breaker to dishwasher.
Remove lower basket.
Drain any water using a wet vac.
Remove bottom cover plate. Should be 2 plastic screws using flat head screwdriver.
Should be able to reach pump. Turn counter clockwise to remove.
Disconnect plug wire on pump.
Install new pump by turning clock wise.
Reattach wire plug.
Run a wash cycle with empty dishwasher and check for leaks.
Replace cover plate.
Done.
Remove lower basket.
Drain any water using a wet vac.
Remove bottom cover plate. Should be 2 plastic screws using flat head screwdriver.
Should be able to reach pump. Turn counter clockwise to remove.
Disconnect plug wire on pump.
Install new pump by turning clock wise.
Reattach wire plug.
Run a wash cycle with empty dishwasher and check for leaks.
Replace cover plate.
Done.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Alan from Corona, CA
- Parts Used:
- W10258275
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Pliers, Screw drivers
The Power Was Completely Of The Dishwasher.
I opened yutube and noted the tips on how to fix specific problems with my dishwasher. That "steve" guy was very helpful. I tested the old bi-metal fuse with no flow and ordered a new replacement through partselect. The part arrived in one day and was fitted quickly. I used the teat meter to confirm that the fuse was ok before I installed it. The only problem that I had was identifying the part and number from a diagram which I did not have.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Conelis from Eclectic, AL
- Parts Used:
- WPW10757217
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver, Screw drivers, Wrench (Adjustable)
The motor was too loud
I took the unit apart to find out what was making the loud noise and found the seal on the main pump had been leaking ito the bearing on the motor.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Lynn from Holbrook, NY
- Parts Used:
- WP8531233
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
The silverware basket just wore out....
Just drop the basket in and its done.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Linda from Incline Village, NV
- Parts Used:
- WP8531233
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
The silverware basket was broken
Simply took out the old tray and replaced it with the new one....VOILA!
The best part about this repair project was the ease in ordering the part from PartSelect. The website was easy to navigate through and the part selection was clear and well illustrated. And then, the part showed up at my home just days after placing the order! Great service!!!
The best part about this repair project was the ease in ordering the part from PartSelect. The website was easy to navigate through and the part selection was clear and well illustrated. And then, the part showed up at my home just days after placing the order! Great service!!!
Was this instruction helpful to you?
Thank you for voting!
Door spring broke-Door falls down
Remove 2 screws on lower baseplate. Remove 2 screws that hold dishwasher inside cabinet( may be attached to counter top or side cabinets). Turn off water supply to dishwasher. Remove any connections such as water supply, electrical connection, or waste water line that prevent dishwasher from being pulled out about 3/4 of the way. With the dishwasher door closed, remove broken parts and replace with new parts. Pull on spring to make final connection of nylon cable. Reverse the above instructions for re-installing the machine.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Dorothy from BILLINGS, MT
- Parts Used:
- W10727426
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
the tines in the upper basket of the dishwasher were falling apart
Removed the old tines by pushing out the clips on the end and then installed the new tines and applied clips - took 10 minutes worked slick and the washer basket looks to be brand.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Debbie from NORWICH, KS
- Parts Used:
- WP8531233
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
Holes in the bottom of the old silverware basket.
I opened the dishwasher door. Removed the old silverware basket and replaced it with the new silverware basket. Then I disposed of the old basket.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Edward from Tucson, AZ
- Parts Used:
- W11196317
- Difficulty Level:
- Easy
- Total Repair Time:
- Less than 15 mins
Dishwasher door leaked
Just removed the old seal and followed the instructions that came with the new one. Since the old one didn't have any adhesive on it ,I didn't use the adhesice on the new one. Problem solved!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Fred from Kernersville, NC
- Parts Used:
- 8269144A
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver, Pliers, Screw drivers
old hose possible leakage
put new hose on, very easy.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- lisa from columbus, NE
- Parts Used:
- WPW10757217
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers, Socket set, Wrench set
front seal on the old pump failed causing the front bearing to get wet repeatedly and fail
Removed required hardware and dishwasher from undercounter mount. Turned dishwasher on its front and removed the old motor. Installed the new motor and tested for function. Installed once test was successful.
Was this instruction helpful to you?
Thank you for voting!
Door just fell down
Hardest part was pulling dishwasher away from cabinet, making sure to not disturb water and drain line. I replaced both door springs which are on the two sides and attached to the dishwasher frame towards the back. This necessiatated pulling the dishwasher about 2/3 out of cabinet. After attaching both springs to frame, replacing the balance kit was a breeze .One screw to remove and then replace with new pulley unit. Attach the supplied cord with attached fittings to spring and then around two pulleys and mounting point on frame. Done . Push dishwasher back into cabinet, reattach two screws to underside of counter. Probably did not require new springs as they seem heavy duty and were not broken upon examination but ordered them also and replaced just in case. Most problem would be with broken cord in balance link kit
Was this instruction helpful to you?
Thank you for voting!