KUDS30IXSS1 KitchenAid Dishwasher - Instructions

First, this replacement kit seems to be of much better quality than the factory original. I was able to remove the old adjuster from the top rack with my hands - did break a little more in the process, but as this was destined for the garbage anyway, I wasn't delicate about it. The new adjuster kit snapped together easily with clear instructions and pictures in a matter of minutes, even with a 1, 3, and 5 year old "helping." Last step requires a screwdriver. I only replaced one side, for now, and it took longer to get the old adjuster off than it did to install new. Done in under ten minutes start to finish and works perfectly!

I removed the dishwasher from under the counter. This took the bulk of the repair time along with disconnecting the water supply and electrical connection. I had enough slack in drain hoses that I could turn the dishwasher over to replace the motor. I was surprised that there was only one bolt that held the motor in place. I put the motor on, turned the dishwasher upright and slide it back unde the counter and began the long process ofreconnecting everything. I am sureit could have gone faster if I were younger and did not need glasses for close work. Start to finish took me four hours. This was the fourth time I have replaced motors in dishwashers of various makes.

Dish rack adjuster kit W10712394: I am a fully inexperienced and non-mechanical mom who needed her dishwasher during this holiday season! It took me a little longer and seemed a little harder than the description said it would - but not by much. The dishwasher is now better than it was when we bought it. Tip 1 - The original mechanism had no screws. The replacement kit does. The kit comes with a special screw that you will need in order to use a phillips screwdriver. It would have been helpful to know that before I tried to screw the screws in and stripped the first one because none of my screwdrivers fit. 2- Instructions aren't clear and photos are a little distorted (2D rather than 3D) for a novice. I wish I'd known this request for installation instructions was coming before I finished the project so I could have taken pictures. Tip - Take pictures to submit for installation instructions for others to appreciate. Would be nice to have some kind of perk to motivate people to do the work of clarifying instructions and submitting pictures. 3 - The part that locks the sliding mechanism into place is a little tricky. That step in the instructions needs some attention. I don't know how to clarify it further but other than the problem with the screws, this is the part that consumed time that an experienced dishwasher repair person might have breezed through.

Removed old gasket, cleaned track thoroughly, then followed instructions from video on Part Select order form. Instructions very clear and precise. Getting the new gasket was a little tedious at the corners but take your time and work the gasket with your fingers as shown on the video.

Disconnected power to dishwasher. Removed water supply hose from inlet water valve.
Removed lower and upper racks. Removed Lower spray arm. Removed tube from pump tp top spinner. Pulled dishwasher from under cabinet (remember to tip to get back out!). Placed dishwasher on its back. Removed electrical connectors from water valve, main motor and drain motor. Removed drain hose from drain pump. Removed pump/motor assy by pulling out wedges and pushing assembly into dishwasher. Removed pump/motor assy from inside dishwasher. Cleaned out pump. Installed new chopper. Re-install pump/motor assy. Re-install driain pump hose. Re-connect the pumps and water valve electric connectors. Slide dishwasher near cabinet for re-install. Re-connect drain hose to dishwasher. Re-install dishwasher under cabinet.Reconnect water supply. Removed top spinner from tube. Installed new spinner onto tube. Re-install tube onto main pump (below lower spray arm). Clean out and re-install lower spray arm. Remove middle spray arm from top rack. Clean out spray arm. Re-install spray arm with a new gasket (gasket may have not been needed). Re-installed lower and top racks. Re-connect power supply. Position all three spray arms pointing towards the door to confirm they were turning. Tested dishwasher - confirmed fill, wash, and drain properly. Also confirmed that all three spray arms were turning. Machine is washing, draining and running great since!

I looked up the repair on youtube and followed along step by step.
I am a 64 year old female and the job was easier to do while watching a repairman than it would have been to read instructions.
The internet is great for some things!

Watched the video. Easy!!!

Prepared by watching the video. Great instructions. Great.

Disassembled easily as per video. Removed the old latch and installed the new.

Began the reassembly and learned that after ten or more years the small plastic parts used to keep the dishwasher steady had slowly deteriorated to the point that I was breaking these necessary items faster than I was putting the appliance back together.

What was a half hour task became over two hours and the end result was for me to put my tools away and buy a new dishwasher the next day. I learned that if your appliance is over ten years old BUY A NEW ONE!

Great job by the people who make and sell the latch parts for you who own a dishwasher that is only a few years old.

Thank you Part Select.

1) clear out the dishwasher
2) remove unit securing screws from top or sides of DW and cabinetry near the top or under the counter top
3) gently pull the dishwasher from the cabinetry about 20" is plenty, mind the connecting hoses and electrical connection
4) close the door! pull back the insulation from the area of the hinge and photograph both sides - this will save you the pain of going online
5) you will see the cord, the tensioning wheel assembly and the door balance spring on both sides
6) with the door closed to relieve tension on the cord, remove the cord from the balance spring - this can be done w/o tools at this point
7) remove the 5/16" screw from the plastic tensioning wheels and remove the tensioners, cord - leave the springs in place if not replacing them
8) install the door end of the cord to its hook on the hinge, install the new tensioning wheel assembly, install the old 5/16" self tapping screw through the lower wheel and into the outer hole in the frame
9) thread the cord from the door over the upper wheel and lower wheel. the lower wheel has cord retaining tabs to hold the cord on the assembly
10) hook the eye end of the cord to the balance spring and you are finished with the first side - repeat operations for the other side, reposition the insulation and slide the washer back in its cavity - do not forget to reinstall the stabilizing screws in the upper washer frame
11) you've done it!
12) have a cuppa and do your second washer that hasn't failed yet - it will soon.

Watched the video and it was perfect. Very easy.

I did not relize that the drain hose was in two parts. Naturally I ordered the wrong half. So after I relized my mistake, I re-ordered the correct part. Once the correct part was received the repair was easy and went well.

I am a 61 year old woman and it took me a total of 2 min. max. Popped it into place and pushed in button that holds it..Taa Daa...perfect!

The old tine row came out easily and the new one was easy to pop into place. I was pleased that it was so easy to order a replacement part.

Unplug dishwasher and slide it out from under cabinet. Remove old broken link (a heavy string between two plastic parts) and replace with new one. Slide dishwasher back and plug it in. Very easy and no tools required.

Turn off breaker to dishwasher.
Remove lower basket.
Drain any water using a wet vac.
Remove bottom cover plate. Should be 2 plastic screws using flat head screwdriver.
Should be able to reach pump. Turn counter clockwise to remove.
Disconnect plug wire on pump.
Install new pump by turning clock wise.
Reattach wire plug.
Run a wash cycle with empty dishwasher and check for leaks.
Replace cover plate.
Done.