KUDE40CVBL2 KitchenAid Dishwasher - Instructions

Removed the old one, cleaned out the groove, dry fit the gasket, made a small cut to fit length, removed, squeezed the glue into the track and then put gasket in. Had to wait 24 hours for glue to cure.
No leaks.

Watch your video about my dishwasher symptoms. Move water tube for upper rack to the right and release lower spray arm. Remove 4 clutch head screws from filter cover and remove. Dig out 10 years of undisolved soap and reassemble.

I spent more time reading the easy instructions several times than it took me to actually do the repair to replace the fuse. I wanted to make sure I fully understood the instructions before I undertook the task. I also checked out a video on You-tube which explained and showed me the same thing as the instructions did. By the time I picked up the screwdriver, I was practically "an expert". I just cut two wires and hooked up two new wires and... done. The instructions were simple....so was the repair. Nothing to it.

The air just unscrews with one twist and the new arm twist right back on. No tools needs. Saved me $100 service call.

I had a common issue on many dishwashers, the final drain cycle was not draining but the pump was trying to turn. Also, the drain pipe was clean. This issue caused a burning smell, like a circuit board heating up. Half plastic smell, half electrical. I bought a replacement pump, followed the pump replacement video instructions from PartsSelect, and it was replaced in under 15 minutes without any tools.

Took off the old wheels and placed them on the new rack - fast and easy if you watch the video.

Removed broken tin row. Replaced with new tine row. Tokk less than 1 minute.

Without the rinse cap appliance was not rinsing properly, partselect made it easy to find necessary information to find part. Had it within a couple of days, replaced the cap within seconds and works just like before.

Take out 6 screws from inside door upper most screws to control panel, removed water safety shield 3 easy tabs to release, found old fuse removed , cut wire 1 inch from old fuse removed have to pull fuse out of its plastic holder put in new fuse matched up wires, they are color coordinated, black with white stripe, and one solid black striped wires and twisted them tight, and inserted them in new wire harness that came from parts select tighten them tide them all together and used black electrical tape on all the new connections put back together and it totally fixed the problem so happy saved alot of money not having to call a service repairman

Due to the way I installed the appliance originally it was not necessary to disconnect supply water nor the drain connections. When the cord broke the spring came out of the point of connection to the appliance. It some "finagelling" to reattach the spring.After some "select vocabulary" it hooked into the correct spot and the rest was history.

remover the nut inside of the dishwasher under the float took bottom plate off open the plastic housing installed new the new float switch plug in the wires snip in the new housing put the unit back in the hole put nut back on and put the bottom plate back on easy as pie

The first try didn't go well. The door didn't stay locked because the new seal was preventing it.
I pulled it back off for the second try and first I let it soak in the hot water for a few minutes to soften the rubber. Then I lubricated it with Vaseline and now the seal got in the grove easily and completely. I believe that that step was critical to ensure 100% success rate. After that everything was fine, the door locked properly, and, of course, there was no more leaking.

I closed the water at the tank and opened all the hot water faucets in the house thereby draining static water from the inlet hose at the valve. Then I unscrewed the inlet hose from the valve, unscrewed the valve body from the support bracket under the tub, unplugged the electrical plug from the valve body, and removed the outlet hose. I installed the new valve using the reverse sequence. Then I closed all the hot water faucets, turned on the hot water at the tank, and purged air from each of the faucets. I then started the dishwasher and ran it through a complete cycle, periodically checking it for leaks, and found none. Total time for uninstall and reinstall - about 30 minutes. Not bad for an 80 year old.

Popping out the old tine rows was very simple and required no tools. The only issue was that the spacing of the replacement tines was different from the original parts and there was not enough space between the tines and the basket to snap the clips back on to hold the tine row. I went to my band saw and cut the extended ends off of the clips and then they snapped into place perfectly. This would have been a 20 minute, no tool job if I didn't have to run to the band saw.

Repaired according to the video attached to the part I ordered. The problem is that though the replacement part look like the one I was replacing, once installed I realized the electrical connector on the replacement part did not match the cable connector from the dishwasher control panel. I called support to find out my options and got a message that because of the scary Covid-19 issue, nobody was available to tell me what my options are. So I have a nice, new, installed replacement part that won't work because of different electrical connectors. I'm happy though that the governors and politicians don't have to worry about things like this. They continue to receive their paychecks and can simply order new appliances rather than try to fix 18 year-old equipment like the rest of us.