KUDE40FXPA4 KitchenAid Dishwasher - Instructions

This repair is simple. However, what you recieve is a box of loose parts and no instructions. The new parts are not remotely the same design as the original. You have to figure out how to remove the old parts (fairly easy by careful prying) but then sort out what the new parts do and how they fit together. It takes patience and some mechanical knowledge. Once you figure it out, it goes quickly. A fairly simple diagram included with the parts would be definite benefit for most people. It seemed like an odd omission. They also include the shortest star driver (about 1 inch long) I have ever seen for the 4 screws but it is useless since you can't really apply enough torque to the screws to properly set them. Be prepared with a standard length star driver.

I opened the package took out the replacement part and installed it with no tools. Easy, done in 10 minutes.

I Removed the upper wash rack by removing locks on each front slide of rack. I laid a towel in the bottom of the washer to keep anything dropped, retrievable. I then removed the top screw closest to the spinner location. I then carefully pulled down on the mounting, which exposed the bad bushing lock. I removed the old bushing lock and replaced with new one. I then replaced the spinner with a push with one hand while holding the bushing in place with the other hand. You will feel a snap as all goes into place. Make sure new spinner spins freely. Now reinstall removed screw. Do not over tighten. Now reinstall lower rack, carefully aligning water feed in rear of washer, and making sure all rollers are back in sliding rack. Reinstall locking tabs onto sliding rack. Now slide out rack, it should not come off slider. Important: now remove the towel in the bottom of the washer. If left in place, you will have a fire during the drying cycle. Close the door and test your washer through a cycle. I felt confident and did a load of dishes. If all went well, spinner should be in place, not in the bottom of the washer.

Pull the old seal out and push the new seal in. Done. Easy. The only issue is the door is still leaking and I have to replace the seal and the plate that goes across the bottom of the door.

Order both this seal and the seal for the bottom of the door at the same time.

First, I bought the door balance link to replace the broken links that connect to the springs.

Because I didn't have enough slack to simply pull out the dishwasher far enough to reach the springs, I had to disconnect the water line and electrical wiring.
The only reason my repair took as long as it did was because there was so little room underneath the dishwasher for disconnecting the water line. I had to buy a shorter adjustable wrench. Also, I had leaks after reconnecting the water line. I had to tighten the compression nut as far as it would go. The nut wrapped around a white substance that had been applied to the threads (I believe this is called pipe tape), which did the trick for sealing the leak.

The repair was a complete success! The parts arrived fast and the information from other customers on the the PartsSelect website was invaluable.

Follow the u tube instruction. Replacing the pump was very simple and easy. The hard part was getting the dishwasher out of the cabinet and back in again.

Put the kick plate under the dishwasher and screwed it in. Easy!

Took half hour to take off old Adjuster just trying to figure which things pop off putting on new one side 10 minute at the most

Removed old housing parts and replaced them with the new parts I ordered. Very easy

At first I thought I needed a new bottom rack for my dishwasher. Out of curiosity, I watched the installation video and realized that the Tine Row installed separately and that was the only part I needed. I am appreciative of being able to access that video and the money I saved. Installation took seconds to complete.

The air just unscrews with one twist and the new arm twist right back on. No tools needs. Saved me $100 service call.

My husband did the repair. It was very easy. He basically just popped off the old wheels and popped on the new ones.

The old filter simply unscrews and the new one screws in.

I had a common issue on many dishwashers, the final drain cycle was not draining but the pump was trying to turn. Also, the drain pipe was clean. This issue caused a burning smell, like a circuit board heating up. Half plastic smell, half electrical. I bought a replacement pump, followed the pump replacement video instructions from PartsSelect, and it was replaced in under 15 minutes without any tools.

These wheel assembly that came on the lower rack of my dishwasher were junk! They started falling off within 6 months. I put them back on to the point that the pin in the center of the wheels would no long stay in place, thus the frustrating situation of the wheels falling off often.

Assembly was easy peasy!