KUDE40FXBT3 KitchenAid Dishwasher - Instructions

I Removed the upper wash rack by removing locks on each front slide of rack. I laid a towel in the bottom of the washer to keep anything dropped, retrievable. I then removed the top screw closest to the spinner location. I then carefully pulled down on the mounting, which exposed the bad bushing lock. I removed the old bushing lock and replaced with new one. I then replaced the spinner with a push with one hand while holding the bushing in place with the other hand. You will feel a snap as all goes into place. Make sure new spinner spins freely. Now reinstall removed screw. Do not over tighten. Now reinstall lower rack, carefully aligning water feed in rear of washer, and making sure all rollers are back in sliding rack. Reinstall locking tabs onto sliding rack. Now slide out rack, it should not come off slider. Important: now remove the towel in the bottom of the washer. If left in place, you will have a fire during the drying cycle. Close the door and test your washer through a cycle. I felt confident and did a load of dishes. If all went well, spinner should be in place, not in the bottom of the washer.

Gently pull the old door seal out of it's track observing the orientation of the seal and the amount of extra seal at the ends of the seal grove/track..
Start installing the seal on one side leaving about the same amount of extra seal as original seal before removal.
Be sure the seals orientation is the same as the seal that was removed.
Carefully pressing the seal into the grove/track designed to hold the seal. Be careful to fully seat the seal into the grove/track.
The corners will be a little tricky, but carefully press and seat the new door seal all the way around. There should be a little extra seal after you get to the end of the grove/track.
Good luck, the new door seal solved my water leak.

Soak up the water in the dishwasher with an old towel. Removed the cover under the dishwasher. Found the pump and twisted it off anti clockwise. Replaced with the new pump. Run a quick cycle, to make sure it pumped out all the water. My wife has used it several times since without any issues.

Removed old housing parts and replaced them with the new parts I ordered. Very easy

Put the kick plate under the dishwasher and screwed it in. Easy!

First electrical power to the dish washer was turned off. The top portion of front door panel was then opened up to expose pocket handle and latch assembly. Old latch assembly was replaced with new latch assembly and a new fuse. The door panel was then re-closed and electrical power turned on.

simply line up the new pin with the rectangular slot in the kick panel and metal panel behind, slide the pin in and turn it with a flat blade screw driver.
NOTE: the original pin was black. A black replacement part cost $29 plus shipping! A knock-off pin was only $6 plus shipping. I got the cheap one and colored it with a black Sharpee marker before installation.

Took half hour to take off old Adjuster just trying to figure which things pop off putting on new one side 10 minute at the most

Watch your video about my dishwasher symptoms. Move water tube for upper rack to the right and release lower spray arm. Remove 4 clutch head screws from filter cover and remove. Dig out 10 years of undisolved soap and reassemble.

PULLED BROKEN CLIP OFF AND SQUEEZED NEW ONE IN. I HAD TO USE PLIERS TO SQUEEZE TOGTHER SINCE i AM 77 YEARS OLD AND HANDS ARE NOT THAT STRONG ANY MORE. I HAD ALSO WATCHED THE INTERNET VIDEO TO MAKE SURE I COULD HANDLE THIS CORRECTLY. 10 MINUTES MAX TO UNLOAD TOP RACK AND PUT TOGETHER.

My husband did the repair. It was very easy. He basically just popped off the old wheels and popped on the new ones.

The old filter simply unscrews and the new one screws in.

I followed another story for the same repair. Worked great.

Took off the old wheels and placed them on the new rack - fast and easy if you watch the video.

Pulled washer out far enough to put 2x4’s under front feet. Removed front panel, I clipped wire connector and unplugged it. Pushed plastic locking lever in and twisted unit counterclockwise. Wiped inner rim and reversed above procedure to assemble.