Models > KUDE20FXWH4 > Instructions

KUDE20FXWH4 KitchenAid Dishwasher - Instructions

Jump to:

All Instructions for the KUDE20FXWH4
121 - 135 of 925
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Customer:
Mark from Seattle, WA
Parts Used:
8194001
Difficulty Level:
A Bit Difficult
Total Repair Time:
1- 2 hours
Tools:
Screw drivers, Wrench (Adjustable)
Dishwasher door falls when opened
First, I bought the door balance link to replace the broken links that connect to the springs.

Because I didn't have enough slack to simply pull out the dishwasher far enough to reach the springs, I had to disconnect the water line and electrical wiring.
The only reason my repair took as long as it did was because there was so little room underneath the dishwasher for disconnecting the water line. I had to buy a shorter adjustable wrench. Also, I had leaks after reconnecting the water line. I had to tighten the compression nut as far as it would go. The nut wrapped around a white substance that had been applied to the threads (I believe this is called pipe tape), which did the trick for sealing the leak.

The repair was a complete success! The parts arrived fast and the information from other customers on the the PartsSelect website was invaluable.
5 of 7 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Paul from HGHLNDS RANCH, CO
Parts Used:
W11177741
Difficulty Level:
Really Easy
Total Repair Time:
30 - 60 mins
Dishwasher door leaking
Pull the old seal out and push the new seal in. Done. Easy. The only issue is the door is still leaking and I have to replace the seal and the plate that goes across the bottom of the door.

Order both this seal and the seal for the bottom of the door at the same time.
4 of 4 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Leslie from LANCASTER, PA
Parts Used:
W10827631
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins
Tools:
Screw drivers
Took off kick plate to get ready for winter shut down
Put the kick plate under the dishwasher and screwed it in. Easy!
4 of 5 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Todd from ROTONDA WEST, FL
Parts Used:
WPW10503549
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins
Tools:
Screw drivers
A plastic retainer pin for the bottom kick panel was missing.
simply line up the new pin with the rectangular slot in the kick panel and metal panel behind, slide the pin in and turn it with a flat blade screw driver.
NOTE: the original pin was black. A black replacement part cost $29 plus shipping! A knock-off pin was only $6 plus shipping. I got the cheap one and colored it with a black Sharpee marker before installation.
4 of 5 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Robert R from FOLSOM, CA
Parts Used:
WPW10195840, W10712394
Difficulty Level:
Really Easy
Total Repair Time:
15 - 30 mins
Tools:
Nutdriver
Roller mount broke Rack Adjuster
Took half hour to take off old Adjuster just trying to figure which things pop off putting on new one side 10 minute at the most
6 of 11 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Larry from MANCHESTER, NJ
Parts Used:
WPW10588164, WPW10250162, WPW10250160
Difficulty Level:
Very Easy
Total Repair Time:
Less than 15 mins
Housing outer piece was broken
Removed old housing parts and replaced them with the new parts I ordered. Very easy
4 of 5 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Cheryl von der from HUNTINGTN BCH, CA
Parts Used:
W10728160
Difficulty Level:
Very Easy
Total Repair Time:
Less than 15 mins
Tine Row Rusted
At first I thought I needed a new bottom rack for my dishwasher. Out of curiosity, I watched the installation video and realized that the Tine Row installed separately and that was the only part I needed. I am appreciative of being able to access that video and the money I saved. Installation took seconds to complete.
4 of 5 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Robert from BOULDER, CO
Parts Used:
W10402110
Difficulty Level:
Really Easy
Total Repair Time:
30 - 60 mins
Tools:
Screw drivers
Faulty door handle shorted out the fuse.
First electrical power to the dish washer was turned off. The top portion of front door panel was then opened up to expose pocket handle and latch assembly. Old latch assembly was replaced with new latch assembly and a new fuse. The door panel was then re-closed and electrical power turned on.
10 of 23 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Sherry from SUSANVILLE, CA
Parts Used:
WPW10491331
Difficulty Level:
Very Easy
Total Repair Time:
Less than 15 mins
The filter came out and pushed the arm up on the burner and melted it.
The air just unscrews with one twist and the new arm twist right back on. No tools needs. Saved me $100 service call.
3 of 3 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Jane from JOLIET, IL
Parts Used:
W10195416
Difficulty Level:
Very Easy
Total Repair Time:
Less than 15 mins
Tools:
Screw drivers
Replaced wheels on lower rack
My husband did the repair. It was very easy. He basically just popped off the old wheels and popped on the new ones.
3 of 3 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
J Kevin from Pittsburg, CA
Parts Used:
W10728159
Difficulty Level:
Very Easy
Total Repair Time:
Less than 15 mins
Tools:
Screw drivers
Rack tines were corroded
Took off the old wheels and placed them on the new rack - fast and easy if you watch the video.
4 of 6 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Martha from SAN DIEGO, CA
Parts Used:
W10872845
Difficulty Level:
Very Easy
Total Repair Time:
Less than 15 mins
Water filter needed replacing
The old filter simply unscrews and the new one screws in.
4 of 6 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Sonya from YOUNGSTOWN, OH
Parts Used:
WPW10195622
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins
Tools:
Pliers
TOP RACK END CLIP BROKE OFF
PULLED BROKEN CLIP OFF AND SQUEEZED NEW ONE IN. I HAD TO USE PLIERS TO SQUEEZE TOGTHER SINCE i AM 77 YEARS OLD AND HANDS ARE NOT THAT STRONG ANY MORE. I HAD ALSO WATCHED THE INTERNET VIDEO TO MAKE SURE I COULD HANDLE THIS CORRECTLY. 10 MINUTES MAX TO UNLOAD TOP RACK AND PUT TOGETHER.
3 of 3 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Jerry from BOALSBURG, PA
Parts Used:
WP8270020, 8194001
Difficulty Level:
Very Easy
Total Repair Time:
15 - 30 mins
Tools:
Nutdriver
Original door balance cord broke on one side
pulled the dishwasher out (took the most time-1 hour) and 30 min. to install new door balance kit and springs. Replace both sides while the unit was out.
3 of 3 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Walter O from CROYDON, PA
Parts Used:
WPW10348269
Difficulty Level:
Very Easy
Total Repair Time:
15 - 30 mins
Tools:
Pliers, Screw drivers
Dishwasher would not empty.
Ordered a new pump (after a online diagnosis). Followed the instruction video on the website...also took the time to replace the discharge hose due to residue buildup...tested dishwasher (one cycle). Slide dishwasher back into opening....DONE. Works perfectly. THANKS
3 of 3 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
All Instructions for the KUDE20FXWH4
121 - 135 of 925