KUDE60FVWH2 KitchenAid Dishwasher - Instructions

I followed another story for the same repair. Worked great.

Removed broken tin row. Replaced with new tine row. Tokk less than 1 minute.

Take out 6 screws from inside door upper most screws to control panel, removed water safety shield 3 easy tabs to release, found old fuse removed , cut wire 1 inch from old fuse removed have to pull fuse out of its plastic holder put in new fuse matched up wires, they are color coordinated, black with white stripe, and one solid black striped wires and twisted them tight, and inserted them in new wire harness that came from parts select tighten them tide them all together and used black electrical tape on all the new connections put back together and it totally fixed the problem so happy saved alot of money not having to call a service repairman

The air just unscrews with one twist and the new arm twist right back on. No tools needs. Saved me $100 service call.

I had a common issue on many dishwashers, the final drain cycle was not draining but the pump was trying to turn. Also, the drain pipe was clean. This issue caused a burning smell, like a circuit board heating up. Half plastic smell, half electrical. I bought a replacement pump, followed the pump replacement video instructions from PartsSelect, and it was replaced in under 15 minutes without any tools.

Without the rinse cap appliance was not rinsing properly, partselect made it easy to find necessary information to find part. Had it within a couple of days, replaced the cap within seconds and works just like before.

Took off the old wheels and placed them on the new rack - fast and easy if you watch the video.

removed kick panel with screwdriver, 90 degree turn of screw. Put towel under drain pump. Disconnect drain hose by loosening spring clip with pliers to provide access to pump. released spring clip on old motor while turning counterclockwise to separate pump from drain reservoir. inspect drain reservoir from inside machine to remove any foreign objects. Installed new pump by indexing attachment flanges to notches in reservoir and turning pump clockwise until locking tab makes audible click. reattach drain hose insuring hose is contacting "stop" ribs on drain hose pipe. Run wash cycle on machine to insure there are no leaks. Re-attached kick panel.

Following the video was quick and easy. Without the video it would have been slow and painful.

Pulled washer out far enough to put 2x4’s under front feet. Removed front panel, I clipped wire connector and unplugged it. Pushed plastic locking lever in and twisted unit counterclockwise. Wiped inner rim and reversed above procedure to assemble.

pulled the dishwasher out (took the most time-1 hour) and 30 min. to install new door balance kit and springs. Replace both sides while the unit was out.

Due to the way I installed the appliance originally it was not necessary to disconnect supply water nor the drain connections. When the cord broke the spring came out of the point of connection to the appliance. It some "finagelling" to reattach the spring.After some "select vocabulary" it hooked into the correct spot and the rest was history.

The first try didn't go well. The door didn't stay locked because the new seal was preventing it.
I pulled it back off for the second try and first I let it soak in the hot water for a few minutes to soften the rubber. Then I lubricated it with Vaseline and now the seal got in the grove easily and completely. I believe that that step was critical to ensure 100% success rate. After that everything was fine, the door locked properly, and, of course, there was no more leaking.

I closed the water at the tank and opened all the hot water faucets in the house thereby draining static water from the inlet hose at the valve. Then I unscrewed the inlet hose from the valve, unscrewed the valve body from the support bracket under the tub, unplugged the electrical plug from the valve body, and removed the outlet hose. I installed the new valve using the reverse sequence. Then I closed all the hot water faucets, turned on the hot water at the tank, and purged air from each of the faucets. I then started the dishwasher and ran it through a complete cycle, periodically checking it for leaks, and found none. Total time for uninstall and reinstall - about 30 minutes. Not bad for an 80 year old.

Popping out the old tine rows was very simple and required no tools. The only issue was that the spacing of the replacement tines was different from the original parts and there was not enough space between the tines and the basket to snap the clips back on to hold the tine row. I went to my band saw and cut the extended ends off of the clips and then they snapped into place perfectly. This would have been a 20 minute, no tool job if I didn't have to run to the band saw.