KUDL15FXWH2 KitchenAid Dishwasher - Instructions

removed kick panel with screwdriver, 90 degree turn of screw. Put towel under drain pump. Disconnect drain hose by loosening spring clip with pliers to provide access to pump. released spring clip on old motor while turning counterclockwise to separate pump from drain reservoir. inspect drain reservoir from inside machine to remove any foreign objects. Installed new pump by indexing attachment flanges to notches in reservoir and turning pump clockwise until locking tab makes audible click. reattach drain hose insuring hose is contacting "stop" ribs on drain hose pipe. Run wash cycle on machine to insure there are no leaks. Re-attached kick panel.

pulled the dishwasher out (took the most time-1 hour) and 30 min. to install new door balance kit and springs. Replace both sides while the unit was out.

leveled dishwasher, it was leaning forward, raised front 1/2'", to get level.
no More leaks, WOULD LIKE TO RETURN DOOR SEAL. DID NOT USE SEAL.

THANKS,
PETE GODSHALK

I took the valve off and actually hooked 110 volts to the vale and tried to blow through it and it would not let air pass through it. I replaced the the new valve in about 15 minutes and it works fine

Removed dishwasher from cabinetry to replace tub rollers (4). Replaced roller sets (4) on top rack. Also replace both rails and rail stops. Screwdriver was only tool required for this part of repair. Needed wrench and screwdriver to remove and replace dishwasher in lower cabinetry.

Turned off water supply to the unit. Removed plastic cover at bottom front. I only had to disconnect the copper water line to slide the unit about 1/3 of the way out. I then was able to reach the wires, disconnect them and use a stubby box/open end wrench (5/8? don't remember for sure) to remove the plastic nuts. I then opened the door, removed the bottom basket and slipped the element right out. Installation of new part was reverse.

I took the top dishwasher rack off, then took off the old clip I had taped on. I hadn’t watched the video so I put the new one on by looking at the other side rail and inserted the new part matching the other rail, clicked the new clip on and I was done. it was quite easy for an eighty-one year old woman!! It did take me awhile to figure it out.

Ordered p/n PS10057154, sold as a kit of TWO upper rack tine rows. I received one. Customer service issued a return tag and ordered a second kit, which again was supposed to be two rows. Replacement order arrived with just one. Fortunately, I had expected this and had not yet returned the first kit. Called customer service and told them not to expect the return of the first order.

This kit is sold as fitting several models of Whirlpool and KitchenAid dishwashers, which I verified that my KA was on the list. A minor installation problem occurred when I discovered that the upright tines of this kit don't have the exact same spacing as the KitchenAid originals. The upright tines need to be exactly half the distance between each of the crossbars on the rack below in order to install the three retaining clips found on each row. With the spacing of these tines, there wasn't quite enough room to install the clips. Fortunately, the retaining clips were manufactured with an excessive amount of shoulder on each one. Trimming off the excess material with a fine-toothed hacksaw blade made the clips narrow enough to be used without compromising their ability to hold the tine rows in place. I've used the machine several times now and the clips are holding everything in place as expected.

[img]https://i.ibb.co/9TQB3mC/clips.jpg[/img]

There was no tools involved the part popped right into place. I received the part within two days from the date placed. It was great.

Something had been loaded in the dishwasher that had gone thru the basket - it hit the arm sprayer and broke it off.

Replacement sprayer was exactly the same - the partselect website has very specific identification method so you get the proper part. You must have your model number.

I watched a you tube video which was referred by part select. This was helpful.

I did not realize at first that only part of the arm sprayer had broken off. The arm sprayer broke off, but there is a base to the arm sprayer that was still attached to the dishwasher. So I could not, of course , fit the new arm with its base over the existing base because they are the same size. Once I realized this, it was a simple replacement, following the youtube instructions. You do have to press and turn counter clockwise to get the old base off, but once that was done, the new sprayer arm, which arrived attached to the base, easily fit, and press hard to turn it clockwise to reattach it..

It has worked perfectly. It is a hard turn to get the arm sprayer off or on, which is good so it doesn't come loose during washing, but when replacing it, you aren't sure of why it won't turn. It is a hard turn. Watch the you tube video.

First remove the front kick panel by removing 2 philips screws. Turn off the water supply, and then disconnect the supply line if not of the flexible kind. Mine was copper. Remove 2 screws holding dishwasher to counter top and pull machine out. Open door and attach replacement link by hooking the plastic end to the hinge hook on the door side and then place the string portion round the plastic pulleys and then attach the other end of the link to the end of the spring attached to the rear of the machine along the bottom side. Push dishwasher back into position, reattach supply line and re-install both screws attaching the machine to the counter top. Turn on the water supply and check for leaks. Place the kick plate into postion and secure using the 2 philips screws that were removed.

At first I thought I needed a new bottom rack for my dishwasher. Out of curiosity, I watched the installation video and realized that the Tine Row installed separately and that was the only part I needed. I am appreciative of being able to access that video and the money I saved. Installation took seconds to complete.

I located the water inlet valve underneath. After moving the dishwasher out from the cabinet, I tilted it . Then I disconnected the black hose with the pliers . Using the adjustable wrench I unscrewed the water feed to the valve . I then unscrewed the valve from the frame and disconnected the wire plug by unlocking and slipping it away from the valve. To install I did all this in reverse.

removed and installed cords with screw driver

I followed the YouTube attached with PartSelect email invoice to fix it. I am very happy PartSelect sent repairing video instruction and took me less than 15 minutes to get it done. Awesome!