KPDC610S3 KitchenAid Dishwasher - Instructions

Very easy,take off the old faucet screen and screw on the adapter. What I really liked was the ease of ordering the part. In less than 5 minutes I had located the part and ordered it. Less than 3 days later, I had the part. Way to go PartSelect.

removed screws from dishwasher and discovered i could replace panel because of door type

we used hot water to soften the ends of the tube and then slid it onto the two ends of the parts in the dishwasher. It did take a little bit of "push" to get it on one end, but nothing we could not handle. I would say anyone with common sense and willingness to fix something them selves would have no problem. I would like to say the part I ordered was of good quality and saved me a lot of money.

I put a whirlpool tube on my Jen more dishwasher . Fits like a glove.

followed the tutorial video and just removed the old one and the new one slipped right on.

ReplacING the tube was not a big job but the old tube had come apart and pieces had lodged in the sprayer arm. I used a toothpick and nut pick to dislodge the pieces and restore full water flow.

Like the video showed but very hard to stretch tube over wider part on interior of top shelf. Read afterwards that hair dryer would have helped. Video should mention that. Bruised hands and wrists getting it on good.

Tranfered wheels from old rack to replacement rack. Silverware caddy was a bit too big for the replacement. I gently bent the prongs on the rack a little and its fits perfect.

Closed water supply--Turned circuit breaker off to dishwasher--removed lower panel on dishwasher--removed the two wires from water inlet valve--disconnected water supply line--removed angle fitting from old valve & installed in new valve--reinstalled new valve & connected water line & 2 wires--This fixed problem.
I ordered part 11:00 1/15/09--Recd. new one 10:30 next morning. VERY FINE SERVICE & PRICE from PARTS SELECT.COM--Thanks.

first-removed all axles from one side of rack. replace with new ones, replace rollers. repeat for other side of rack. VIOLA!!

I took out the bottom rack, turned it upside down, popped off the wheels and saved them and put on the new axles. It took a little doing to get the new axles snapped into place-they were stiff. I finally figured out how to use the pliers at the right angle to pop them on. Then the wheels popped right on and off I went.

I ordered all new axles even though not all of them were broken - I figured it was just a matter of time. Ordered one new roller because one was missing, and an extra one just in case. Removed all old rollers and axles. A couple of them did not want to come off, so I "hit" them with a screwdriver. Put on all new axles and replaced the rollers. The whole project took about 10 minutes. SUPER EASY. CHEAP FIX FOR MY OLD DISHWASHER.

The website had great pictures, I compared the wheels I had and the broken axles with the pictures, and picked what I thought would match. They were perfect. I used pliers to pop the axle on, and my fingers to put on the wheels. It works perfectly now

Repair was awful without instructions. Instructions were requested twice with no response. Attempted without instruction and broke the sleeve. Reordered but not through Partselect

Finally listened to advice of others online and decided to replace inlet valve. Btw, the problem is NOT the inlet screen. It was completely clean in my case. Issue is with internal seals that swell over time and restrict flow leading to low water level.

Unplugged unit, removed lower front panel (two screws on outside upper corners), undid compression fitting on inlet supply line, removed two screws holding valve bracket to frame, disconnected electrical connections to valve, used pliers to compress hose clamp to remove valve outlet hose, used adjustable wrench and some elbow grease to remove small inlet elbow (its on tight!) from valve inlet, put teflon tape on elbow threads to reinstall on new valve, reverse removal instructions to put everything back. All done! MUCH cleaner dishes!