Models > KIDS42EPSS0 > Instructions

KIDS42EPSS0 KitchenAid Dishwasher - Instructions

Jump to:

All Instructions for the KIDS42EPSS0
1 - 15 of 309
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Customer:
Scott from Fort Lauderdale, FL
Parts Used:
8194001
Difficulty Level:
Easy
Total Repair Time:
Less than 15 mins
Tools:
Screw drivers
Replaced Hinge Link
Pulled dishwasher from under counter, attached link to spring, hooked spring back into frame/chassis, threaded link through pulleys, attached other end of link onto door, reinstalled dishwasher under counter. All's well. Note-I purchased an extra link anticipating that the other one will fail. They're cheap enough.
636 of 690 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Sean from Ramona, CA
Parts Used:
8194001
Difficulty Level:
Easy
Total Repair Time:
15 - 30 mins
Tools:
Screw drivers, Wrench (Adjustable)
Door spring link broken
1. Open the dishwasher and remove the two plastic grommets about halfway down on either side of the opening. Then remove the two screws under the grommets.

2. Remove the kick plate under the door. May have to lower unit by turning the feet using the adjustable wrench.

3. Make sure you have enough slack in the water input line and electrical wiring that you can pull the dishwasher out about 12 inches or more.

4. There is a spring and nylon rope link on both sides of the unit. Probably just one link is broken, but the replacement comes with two, so you can replace both or save one as a spare. Look at the good side and it should be pretty self explanatory how it attaches. I found it easiest to first thread the link around the lower pulley, then attach the link to the spring, then spring to the rear support, then the link to the door.

5. Reverse (2 to 1) to reinstall the dishwasher.
162 of 205 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
David from La Quinta, CA
Parts Used:
8194001
Difficulty Level:
Easy
Total Repair Time:
30 - 60 mins
Tools:
Nutdriver
The door would drop open when it was released
This was the second time I had this problem so I knew the symptoms and remedy. The tools needed were two nut drivers a ¼” and 5/16” along with a flat pry bar and Phillips screw driver. I started by removing the lower front panel by removing the two ¼” screws on either side. The lower panel will lift up and then can be removed by pulling on the bottom. There is a flat sheet metal piece behind the front panel with insulation that can be removed very easily along with the front panel. When the front panel is removed it exposes the front legs that may need to be dropped to let you lift the dishwasher over the tile (if you have ceramic tiles). The next step would be to remove any ties to the counter top if it is attached. Mine were attached by the two straps on either side with Phillips screws. After the top is free, lower the front legs by lifting the dishwasher with the flat pry bar and threading the legs up into their holders. With the legs lifted the dishwasher can be pulled out to expose the tension springs located along the sides at the very bottom. Chances are the ropes are broken off the plastic holders that fit over the door hooks.
Remove the plastic guides by removing the 5/16” nut from the middle of the lower roller. Remember to note which hole the screw is coming from this also sets the tension for how fast or slowly the door drops. Placing the nut closer to the front will drop the door slowly and toward the back will drop the door more quickly. I placed mine in the middle hole. When the plastic guides are removed attach the nylon pope to the spring and attach to the back of the dishwasher. There is a hole located on a flat piece of sheet metal the spring will attach to at the back of the dishwasher (if it is broken). Check the other side if it is still in tact. With the spring in place weave the rope around the plastic guides then pull the springs to help get the plastic end over the door hook located at the bottom of the door. Repeat this operation for the other side (kit has a both sides covered) and reinstall dishwasher in cabinet.
Steps
1) Remove front panel (1/4” nut)
2) Release Dishwasher from Cabinet
3) Lower front legs
4) Pull Dishwasher out from under Cabinet
5) Remove Rope Guide (5/16” nut)
6) Install new Rope Guide (Supplied in Kit)
7) Attach new rope to Spring and attach spring to dishwasher
8) Weave rope through rope guide
9) With door closed pull spring to relieve tension so rope can be attached to door
10) Repeat for other side (Kit has both sides)
127 of 153 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Jeff from Boaz, KY
Parts Used:
675813
Difficulty Level:
Easy
Total Repair Time:
Less than 15 mins
Tools:
Screw drivers
Touch pad on dishwasher dead
1. Remove the two screws that attach the bottom cover.
2. Remove the 2 screws that attach the door outer cover.
3. Remove the 8 screws that attache the door inner cover.
4. Remove the plastic cover over the electronic controller.
5. Remove the two connections to the thermal fuse.
6. Remove the thermal fuse.
7. Install the new thermal fuse.
Reverse the above steps.
114 of 134 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Brad from Woodbury, MN
Parts Used:
675813
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins
No power to dishwasher.
Unplug the dishwasher. Simply removed 8 screws on the inside of the door, removed the interior door panel. Next popped of the plastic protective electrical panel cover. Locate the Thermal fuse that had simple instructions provided. Removed the fuse and replaced the harness. Put everything back together. Plugged dishwasher back into electrical outlet...Dishwasher resumed with the cycle that the dishwasher was in when the fuse blew. Simple, Fast AND Reliable!!!
36 of 43 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Stephen from Galt, CA
Parts Used:
8194001
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins
Tools:
Pliers
Plastic clasp on door spring broke
Pulled dishwasher out from under counter. Relaced cord with plastic hook attaching spring to door. Very easy.

Very impressed with Partselect.com. Full schematic of dishwasher made it easy to select part.

Delivered in 1 day. Fantastic. Highly recommend
29 of 35 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Ronald from Garland, TX
Parts Used:
675813
Difficulty Level:
Easy
Total Repair Time:
15 - 30 mins
Tools:
Nutdriver
The machine just quit in the middle of a cycle and there were no lights on the control panel
There were eight of the star head screws to remove to take the front off the dishwasher, then just followed the instructions that came with the part, which was a thermal fuse and the new wiring that accompanied the fuse in the order. The hardest part was getting the old wire out of the harness with the other three, but once I figured that out just slid the new wire into place and made the connections. I reinserted the screws, turned the power on and knock on wood shes still working.
30 of 39 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
David from Bay City, TX
Parts Used:
4318273
Difficulty Level:
Easy
Total Repair Time:
30 - 60 mins
Tools:
Nutdriver, Screw drivers
Dishwasher stopped in middle of wash cycle..
I disasembled the inner door and replaced the door switches with new ones.
29 of 42 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Jay from Alexandria, VA
Parts Used:
4318273
Difficulty Level:
A Bit Difficult
Total Repair Time:
30 - 60 mins
Tools:
Pliers, Screw drivers
Dishwasher would not turn on. Switch fuse broke.
I removed inner face of door, cut wires leading to door switches, and then installed the new door switches and wire harness.
25 of 32 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Deb from LaPorte, IN
Parts Used:
WP8269208
Difficulty Level:
Easy
Total Repair Time:
1- 2 hours
Tools:
Nutdriver, Pliers, Screw drivers, Wrench (Adjustable)
Stopped Running,Will Not Start, and Clean LED Blinks 7 times then repeats
Got Maintenance Flyer out an read about problem
Removed access plate
Disconnectd water and drain
Removed anchor screws
Pulled unit out and disconnedted from Electric
Flipped on it's back
Ohmed out all heat related items and found discrepency with Thermisitor resistance
Ordered and received Part
Changed out Thermisitor
Checked wiring to Heater and replaced connections
Hooked electric up
Ran Diognostics per Maintenance flyer and cleared fault
Hooked back up and ran like a champ

The reason it took so long is because I put the old thermisitor back in and tryed to run the diognostics just to make sure that was the problem
24 of 31 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Nat from Raleigh, NC
Parts Used:
4318273
Difficulty Level:
Easy
Total Repair Time:
15 - 30 mins
Tools:
Screw drivers
it would turn off and on mid-cycle and finally quit completely
I turned off the circuit. I removed the interior side of the door and then the plastic covering over the electrical wires and switches (I counterbalanced the door with a couple of half gallon juice containers). I removed the wires attached to the switch on the door handle and the door handle itself. The handle and switch parts disassembled and I replaced the switches (part of kit). I cut off the singed wire and the other three beyond the damaged portion and stripped the wires and connected the extensions (part of kit). I attached the new wires to the switches and closed up the interior door. Lastly, I turned the circuit breaker back on. All was well!
20 of 26 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Randall from Moreno Valley, CA
Parts Used:
8194001
Difficulty Level:
Easy
Total Repair Time:
15 - 30 mins
Tools:
Screw drivers
Broken Door Links
Remove two screws at top that fasten dishwasher to cabinet. Slide dishwasher out to expose the two links that attach the door to the springs. Fit the new links to the springs and door.
15 of 16 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Joellen from Castro Valley, CA
Parts Used:
8194001
Difficulty Level:
Really Easy
Total Repair Time:
15 - 30 mins
Tools:
Screw drivers
Dishwasher door falls down as soon as it is unlatched and moved just a few inches open
This kit comes with the link cords and the balance wheels. I only needed the cords. I undid the set screws under the counter edge and slid the Dishwasher out from under the counter. One of the links had a broken cord and the spring had snapped to the very back of the space and was a bit hard to find. I used the good side as a guide to see how to thread the cord correctly. I did not replace the wheels since they appeared to be in good shape and looked like they might be a bit more difficult to replace than just the cord. For a second I thought I had ordered the wrong part because the new cord's attachment point at the hinge did not look exactly like the originals but the new design worked just like the original. I did need one other person to help stretch the spring and hold the door in the best position so I could attach the cord to the hinge. It's working perfectly now and I saved the wheels in case I need them later.
12 of 12 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Peter from San Diego, CA
Parts Used:
WP8269208
Difficulty Level:
Really Easy
Total Repair Time:
15 - 30 mins
Tools:
Screw drivers
Dishwasher's "clean" light just blinked - wouldn't run. Repairman came and found out problem and suggested I could fix it myself
Since I had watched a repairman diagnose the problem, it was eash to reproduce how to pull the unit out from the wall and find the faulty part to remove it and replace it with the new thermistor. Two wires to disconnect and connect and repair nearly complete. Pushed it back in, screwed it back to the cabinet and installed foot plate and done.
15 of 22 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
John from Minden, NV
Parts Used:
8194001
Difficulty Level:
Really Easy
Total Repair Time:
30 - 60 mins
Tools:
Screw drivers, Wrench (Adjustable)
Noisy door
I found instructions on line when I goggled my dishwasher name and model number with the words noisy door. There were three or four good suggestions at a couple of the sites I visited. I tried applying vasoline, then silicone to the rope where it travels through the plastic guides but that just cut the sound down about 50%. My dishwasher has plastic guides that look like rollers but they don't turn, they are fixed in place. The ropes squeak as the pass over the guides. The replacement part kit has plastic guides that turn like wheels now so the rope does not drag over them and squeak. This repair could be done by me in 20 minutes or less every time now that I know what I am doing.

I removed the black bottom metal cover then turned the nuts on the adjusting (leveling) bolts to lower the front end of the dishwasher so I could pull it out of the cabinet. Once I lowered is as low as it would go I opened the door and pushed down on it which tilts the dishwasher down and you pull out on it and the top lip clears the cabinet. If your dishwasher just pulls out the first time you try these steps may not be necessary.
Once the dishwasher is out the guides and rope are down at the bottom in the front by the door. It's obvious what to do to replace them.
14 of 22 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
All Instructions for the KIDS42EPSS0
1 - 15 of 309