KUDB23HY2 KitchenAid Dishwasher - Instructions

Removed the old part. It came out with no problem
due to being brittle and cracked. This part was original to my 15 1/2 year old dishwasher.

Ran hot tap water in the sink and soaked the new "Rubber Water Delivery Tube" for about 5 min. I put a little dish washing liquid on dishwasher part where tube was to be slid onto. Including the soaking time,repair took less than 5 1/2 min.

I'm very pleased by the fact that my part arrived in a little over 1 1/2 days.

Was lucky the part was available. I put liquid detergent on both ends of tube, then slid each end onto each sleeve. Works great now!

I removed the old tube. I rubbed vegetable oil on the inside of both ends. The new tube slipped on with no
problem, and that was the end of the repair.

For several years I endured difficulty in pushing in and pulling out a fully loaded lower dishwasher tray in my KitchenAid Superba dishwasher. The tray would "fall out" out of its "track" and jam requiring me to lift up the whole tray to try to pull it out. Then one of the plastic roller "axles" broke and its wheel fell off. So I went on to Part Select's website to find a replacement. When I got it in the mail I replaced the one that broke. I noticed how much more rigid the wheel then ran on its "track." So I replaced all the roller axles and, lo and behold, the lower tray does not jam anymore. It rolls just like new! I am very satisfied. Chris from Bay Ridge, Brooklyn

Took the tube off and noted that there was a factory drilled hole on the underside that lets water drain. I slipped the new tube over the inlet port and the other end over the rotating washing arm aparatus port and everything worked fine. Very easy and fast repair.

The replacement worked fine, but the website could have been a bit more re-assuring in terms of showing the image of the part. It was not possible on the website to determine whether the piece was going to fit, as the piece as shown was flat/oval on both ends, where the fitting for the water feed is round. The site could have explained that this was flexible material that would form itself to the round feed connection. The measurements of the part should also be given. The price was right, so I bought it anyway, and hoped. As I have said, it DID work fine. You need to clarify the item on the website.

The tube had holes from being used but the dishwasher still works great. I researched this part and it was a great price and really easy to fix. The picture looks different than what the tube looks like in the dishwasher but it is correct. Definitely put soap on the ends to help glide it on. Took me 2 minutes to fix.

This was sooo easy. The key was the "tip" on this website to lubricate the parts with dish soap. They slid right on. It works perfectly. Most important, I am a Hero with the wife ... that gets special rewards!!

It was 94 degrees that day so I set the rubber hose outside in the sun to loosen it up, make it more plyable. I then mixed up some soapy water and doused the ends of the hose with the soapy water and slid the hose right onto the fittings.

There was a small hole in the hose which was not discussed in the directions. I assumed the hole should be installed on the down side to let water drain out after the dishwasher is finished. This will reduce the chance of bacteria building in the hose.

I read the installation tips before I started and picked up the soap mix and heating up the hose before installation. Can be accomplished with a hair dryer if it is not 94+ degrees outside!!!

Thanks,

Jim

connected tube to spray arm and attached to back of dish wash machine.

I was goingto go to Home-Depot, and purchase a short piece of tubing to make the repair.
Just for the "heck" of it, I looked on-line --- and there it was. It is a large diameter thin wall tube, because water presiue is low, almost zero.
However, the replacement part was only $8,25, so I figured, what the heck, I can wait a few days and purchased the part from PartSelect.com. I lubricated the new tube with soap, to make the slip-fit go on easier and -------------- Done

Very easy ......... Thank you

Old roller wheels and axles were broken and already falling off. I simply replaced the roller axles and snapped on the new roller wheels.

Simply inserted the new rubber hose on the two fittings - a couple of minutes at most

simply pieced together the "tube"

I pulled out the old hose and pushed in the new one. Took a little muscle, but was glad that it fit. On line site very helpful with description so that it fit perfectly!