KUDP01DLBL0 KitchenAid Dishwasher - Instructions

Checked grinder and cleaned it several times, adjusted blades. Dishes would be clean for approx. 6 cycles, then would not clean. Placed dishwasher on its front and removed the motor. Removed grinder and impeller which I found to be worn so that the blades would not turn on the grinder which caused it to collect food particles. The impeller locks in easily.

I removed the 6 torx screws that hold the control panel on the top part of the door, from the inside, removed the large plastic cover from the control board, removed the 2 big wires that go to the thermal fuse...tested for continuity and foung the fuse faulty...ordered a new fuse kit, reversed the procedure and it works like new.

In less than 5 minutes, we removed the stopper on the end of the arm that held the top rack, slid off the top rack, rotated off the broken wheel assembly, rotated on the new one, slid the rack back on, and replaced the stoppers.

I shut off the power to the dishwasher, then I removed the front panel under the door. On the right side just behind the electrical box there are two wires going up to the hi-limit thermostat, (you may need a small mirror to see it), remove one screw that is holding the thermostat bracket, unplug the wires from the old thermostat and install new one. Screw bracket and thermostat back to the underside of the dishwasher, reinstall the front panel, turn on the power, done.

The upper spinner fell off with each wash and I had been putting the pointy tac-like piece back into the washer type piece, but they did not hold. I ordered the whole kit (spinner was not needed but came with the set). The tac-looking part was the problem, it had been worn down with use. When pushing the new pieces together to hold the upper spinner back in place it was 100% fixed. Took about 10 seconds. Good luck!

Replacing the actual part was easy. Getting to it was the slightly difficult part. Here's how it went:
Remove the torex type screws surrounding the inner door - this was the easiest part. The screws came right out, but be careful. Removing the screws near the top (was controls) part will release the seaparate top part. Once you do that, it's only held by wiring, and you don't want that to break, so treat this part with care.
Remove the bolt screws holding the outer door to the inner door - so the inner white door containing the dispenser to be replaced, and the outer door separate, but are held together by these bolt screws. You need to remove these to separate the doors further giving you easier access to the dispenser. Some of these bolt screws were in challenging positions to reach.
Disconnect dispenser wiring and replace part - Remember where the wires go, so mark them before removing them. The part is held in by 6 bolt screws. Once removed, the part easily came out. Pop the new one in, screw the bolts in, plug the wiring back up.
Put all parts mentioned previously back together.

Now even though we gave the correct model # of our unit, the part sent did not match 100% what we replaced. There was an extra wire plugged to ours. The connector to plug it to does not exist on the new part. My assumption is this wire is for detection of rinse agent (illuminates a ligth on the front panel if empty) - so we just left this unplugged. The new part has a manual, visual gauge on it anyway which I prefer, so this was not a big deal. This is just warning for others that do this kind of thing.

All in all, it was a well worth it repair. $50 as opposed to $500 for a new unit and installation. We will definitely be looking to this site again for items we feel can be repaired. THANK YOU!

Popped out old wheel housing. Popped in replacement with a little help from a flathead screwdriver. Easy.

Several hours to diagnose problem: Removed all the plastic water distribution tubes to top rack and found no blockages. removed lower water jets, drain screens using star driver on 6 screws. still could find now blockages. decided problem had to be in pump mounted below unit so completely disconnected unit and removed from under counter. Upon removing lower plate below door I discovered a plastic pouch containing an excellent trouble shooting guide with complete dis-assembly instructions and parts breakout diagrams with P/N listings! First thing I discovered from this was that the chopper assembly was hiding under a plastic cover just under the filter screen I had already removed. The trick was to press down on the right side of the plate to get it to pop up and reveal the chopper. The whole chopper assembly slides out without tools. I found the strainer plate behind the chopper blade totally plugged as the blade had broken off the plastic drive shaft because the retaining knob on the end of the shaft had broken off. I was able to drill and tap the shaft and install a SS machine screw with washer to reassemble the chopper blade on the shaft. Not expecting this "Joe Maggee" repair to last more than a few cycles I went online with the P/N and googled PartSelect. Placed the order and chose std delivery over 2day or next day since I expected the repair to last for the week. I put everything back together and the first load came out perfect! This was Sunday afternoon. Tuesday the part arrived at my doorstep! 15 minutes and the new part was in. My "Joe Maggee" repair is now in the junk drawer awaiting the next pistachio shell that gets run through the washer.

This site is wonderful..., thank you. Especially thanks to Nanette's detailed experience. The thing that gave me the most problem (and apparently Nanette, as well) was removing the lower round cover of the chopper assembly. Finally, some one on the internet identified the trick...put needle nose pliers in the screw-hole and pull-away. It came right out. Wish I could acknowledge the source but now can't find it.
Actually, the check valve was good, but I replaced it anyway. It was 10 times the trouble to replace than the drain pump. Wish I had started with the drain pump. By removing the drain hose, I stuck my finger in the hole and discovered the problem: the impeller was off of the pump and lying in the bottom of the drain. It was a simple thing to replace the pump. Press down on the locking mechanism and turn it to the left. When it was off, I could see that the check valve was in place and not a problem. (Of course by that time, I had already replaced it.) Good luck.

To empty the water in the dishwater basin, I pushed the cancel button and closed the door. I then turned the electrical breaker to the off position that supplies electricity to the dishwasher. I confirmed the power was off by attempting to start the dishwaser. I removed the metal plate between the dishwater door and the floor by removing the two screws. I removed the two screws that connect the top of the dishwasher to the underside of the countertop. I shut the water valve that supplies hot water to the dishwasher (mine was located under the sink). I disconnected the drain hose (plastic) by using pliers to loosen the clamp the holds the hose on the outlet of the drain pump (drain pump is much smaller than the pump that needed replacement). A towell is handy to soak up the water that comes out the hoses. I loosened the nut on the water supply hose (this was difficult because of lack of room)using a wrench and pliers. I opened the door on the metal box that houses the wire nuts for the electrical connection to dishwater, and I removed the wire nuts and the screw for the ground wire. Once the white, black, and gound wires were disconnected, I could pull the dishwater out. I also had to pull the drain hose out from the clips on the side of the washer to pull the dishwasher out into the middle of the kitchen floor. I flipped the dishwasher on its back. I removed the single bolt that held the broken pump motor to the dishwasher, and then the motor twisted counterclockwise and I pulled it out. The pump shaft would not turn freely with my pliers, so I knew the motor was broken. I removed the pump end (impeller) from the dishwasher by tapping it with my screwdriver. The impeller end came out along with a metal screen. The metal screen was 50% plugged, so I cleaned it and put it back in place. I wet the gasket on the new pump motor and slid it back in place while rotating clockwise and locking it in place with the tabs. I replaced the bolt that holds the motor in place and reversed the repair procedure to re-install the dishwasher. Be sure to run the dishwasher and look for any leaks. The last step is to replace the metal plate between the floor and door. While I had the dishwasher pulled out, I discovered another problem with the pulleys and strings that prevent the heavy door from flopping down, but I won't include this repair. The pump and motor must have been failing for some time because the dishwasher is much quieter now and the dishwasher is much faster. I am sure the plugged screen didn't help either.

removed both upper and lower racks. removed lower spray arm(left hand thread) removed "water delivry tube and upper spray arm. removed torx screws on pump cover. removed inner chopper cover. Chopper assy had come apart and was full of food crud. cleaned out and installed new chopper assy. kind of tricky don't force it. reassembled. tested OK.could tell sound of more forceful water pressure

Pulled dishwasher out from under counter. Relaced cord with plastic hook attaching spring to door. Very easy.

Very impressed with Partselect.com. Full schematic of dishwasher made it easy to select part.

Delivered in 1 day. Fantastic. Highly recommend

This unit was unique that whole motor assembly was held in its place by two plastic clip. The gasket had few rings that worked as place holder, although gaskets don't go bad often this model could be if it gets pulled alot and if motor assembly get pushed it will push up the gasket and cause a leak. Repair was simple, 1) take spray arm off from inside. 2) get under neath the dishwasher, take off wires so it would free up some room, pulled two plastic holder out, gently push the motor assembly up to the tub, 3) from inside the tub, pull up the assembly enough to get your hand under the gasket and pull them off. 4) Replace the gasket, align the assmebly and push down to snap in the gasket. 5) get under and push in two plastic clip back in, put wires back into its place. Back in the tub to push down the assembly again to make sure there are flush with surface. Put spray arm back on. Finished.

Pulled out the old basket.
Threw it out!
Put in the new basket. Perfect fit and color match!
I am very wimpy when it comes to household repairs but this was so easy and quick! Part came in less than one week!
Very very satisfied!

Started as dishes not getting clean and I observed that the top arm was not spinning and there was very low water pressure coming out of the jets. After making sure the water level was up to the bottom of the heating element and making sure the jets were not clogged I checked the filter and chopper. It was a little tough to get the cover off of the chopper but once I did I could see that the chopper scraper was broken off and the shaft was broken. The screen was all clogged up with stuff. Ordered a new assembly and put it in making sure to compress the spring and make sure the gears lined up. Now it is running great.
I think the Kitchenaid is the same as the Whirlpools.