KUDH23HY0 KitchenAid Dishwasher - Instructions

The repair was very easy. The screen was a large
plastic ring with a split opening. I placed it under
water sprayer arm, got it into position on the bottom of the dishwasher, and snapped the split opening together. Job was done in less than 5 min.

I am pleased with your service and the prompt
shipping of my parts order. I would do business with you again. Thank You

First I removed the screws holding the broken mounting brakets in place on both the left and right side and replaced them with the new brackets. It was relatively easy and now the 15 year old dishwasher in addition to still working well is held securely so that it doesn't lean forward when both upper and lower trays are extended.

I removed the clip holding the old tube in place, pulled it off where it was attached to the upper rack hub and removed the cone shaped coupler from the back end of it. Attached the coupler to the new tube, pushed the tube onto the hub and re-attached the clip. Started up the dishwasher after putting in a few glasses into the top rack and they came out clean! Amazing how functional parts make a difference. BTW, the new rubber tube arrived 2 days after I placed my order... very quick service. Thank you very much.

first I removed lower basket. then removed lower sprayer attached to pump housing by unscrewing the cap by hand. the I removed the pump cover . there were six alan screw two of them were missing causing the failure of the seal spraying solution at the door. replaced the pumpseal working backwards until everthing was replaced.

actually my wife did the repair. she unsrewed the water sprayer and removed it, then unscrewd the star key screws and then replaced the seal. she put everything back the way it was and it is now ready to use and we no longer have the problem.
just a suggestion...if you take some baking soda and some vinager you can clean the drain out. just simply poor in the soda and then the vinager.and it will fiz cleaning your drain.

First I removed two lower panels at bottom of dishwasher beneath the loading door using nut drivers. There had been a problem in that the dishwasher was not filling with water during any of the cycle. I closed the water supply. I removed the old water inlet valve completely using pliars to open the hose clamp at the outlet anbd remove the hose. Then used a I/2 "" wrench to remove the copper inlet line. Then I used a screw driver to remove the inlet valve mounting screws. I put the valve in my garage vise to remove the pipe fitting. Everything was reusable on the new valve. I just cracked opened the water supply to make sure water pressure was available to the valve inlet side and reassembled everything. Started the dishwasher and problem solved.

PartSelect web page helped me determine the problem and the solution. It took me longer to read the fix-it directions than it did to fix the dishwasher. Just push the part in the hole and twist. When my wife got home she was so impressed that it was fixed and we didn't spend a huge amount to have a repairman come to our house. I got so much prasie that I didn't tell her how easy it was to do the repairs

First I tried duct tape until I could figure out how to get the part. I went online and found that part that I thought it was, but I wasn't sure since the tube I had was very stiff and looked like it had a particular shape on each end..the one on the site was just a straight tube. I removed the old part which was easy, it pretty much fell off and then pushed the new one on and it conformed to the ends needed since the rubber was soft. It was so easy and the machine works really well again!

Fairly simple to replace the valve. Water input side was a rubber hose that required pliers to squeeze the ring seal and slide it down the hose. Copper pipe on the output side was attached with a 3/8 compression fitting.

I did need to transfer a brass elbow from the old part to the new one.

Had to cut one end of old tube off with pocket knife, other end was cracked and came right off. Put a dab of vasoline in each end of new water tube and slid in place. Wife had called a repair shop, was told $25.50 for part, $65.00 house call/labor. Easy fix with 15.00 +/- part and 10 min. of my own labor.

I first removed the old rubber water delivery tube ( not hard to do since it was literally falling apart from age). I then used a blow dryer to make the new rubber water delivery tube a little more flexible. I slid it on one end and then the other. My dishwasher works great now. The part was very reasonable ($15 with tax & shipping). Last month I had paid Sears to come out to just look at my washing machine and it cost $139. Then the part was going to cost $200 with another $139 because they would have to come out again. I ended up buying a new washer. I was so excited that I was able to fix my dishwasher, I've been telling everyone.

pulled old actuator base off, followed instructions on how to install new actuator - followed them -
piece of cake.

Thanks

Srewed it back on. . . Very simple!

I was told I needed a whole new dishwasher arm, that I probably would not be able to change myself. Described the part of the part in your description area and lo and behold, there it was..
Could not find it anywhere else.
Very proud of myself for fixing it. I did not need any tools. Just removed the old corroded tube and attached the new one.
thanks so much for the web site images and descriptions. (And I normally am very computer /technology challenged) Very user friendly site

Disasembled pump to find dammaged parts replaced with new parts . Made wife very happy .