KUDS01FLBL1 KitchenAid Dishwasher - Instructions

Replaced the switch, that did not fix it, but a new circuit card did

Replaced track on left side.

Removed back of door to access the screws holding on the air inlet. The top of the door with the controls does not need to be removed, I found out--only the bottom part. Accessing the 5 screws was difficult as there was no space to get the socket onto the screws at a 90 degree angle. Also, there are two plastic shields that fall off when you remove the inlet that need to be replaced, with difficulty because of the accessibility to the area.

PartSelect site is excellent and finding the correct part was relatively simple, although I was not absolutely sure I ordered the right part until it arrived--only one day after ordering, although I paid for the least S&H option.

After replacing broken door cables I had a small leak at the door corner. I replaced door seal with that not fixing the leak and found that the door hinges were bent a little from the cables being broke for awile. Installed new hinges and leak is fixed now. A little difficult but once unit was pulled out about 6 inches the hinges were not bad to replace

I removed the old seal and carefully cleaned the track into which the seal was fixed. No tools other than some ordinary cleaning liquid, cloth and small wooden piece to swab out the track. Easy and quick. As a note here, I first used the incorrect schematic for the unit and ordered the wrong seal. However after receiving the wrong part, I made the correction and reordered. I did this over the phone as I needed instructions to return the part. The person taking my order and answering my questions was very helpful and I want to take this opportunity to thank her.

removed old fastener part (broken) from bracket

placed new fastener above bracket

aligned spray arm below bracket

snapped lower fastener part into place

couldnt be easier so long as you have two capable hands and eyesight

Unplug dishwasher and slide it out from under cabinet. Remove old broken link (a heavy string between two plastic parts) and replace with new one. Slide dishwasher back and plug it in. Very easy and no tools required.

I did not relize that the drain hose was in two parts. Naturally I ordered the wrong half. So after I relized my mistake, I re-ordered the correct part. Once the correct part was received the repair was easy and went well.

1. do not order or buy anything before examining the tension nut and washer. 2. Unplug the unit. 3. Open the switch box before trying to remove the float. Two types; easiest is pin based and lifts out easily. If the float catches, it likely has a headed bottom and needs an assist to lift past the stop flanges. 3. Using a standard ohmmeter, check for continuity. If it checks no need to replace. 4. Check float and assembly for abnormalities; cracks, lime deposits, etc. 5. Now decide what needs replacing. Did all my work with relative ease without pulling out the appliance. A couple sequences may need realigned.

Pulled front panel and replaced door switch. Extremely easy but did not fix the problem.

I began by opening the door to the dishwasher. The front panel on this unit is a custom wood panel held on by six screws. I removed the screws and the front panel. Then I unscrewed the two remaining screws holding the control panel onto the door. I also removed the two screws holding the door latch in position. With all screws removed the control panel simply slid off the top of the door. Inside the control panel, I used a small screw drive to pry the retainer clips back from the edge of the electronic control board. The control panel then snaps out. I disconnected the ribbon cable from both boards and reinstalled the new ribbon cable. I then reattached the ribbon cable to the new electronic control board and snapped the new control board into place. I reinstalled the control panel and tested the "Normal" position to insure the dishwasher would respond appropriately. After checking for proper operation, I reinstalled all screws,including the door latch and the front cover. Operation complete.

I procrastinated with the repair thinking it would be a head ache... But googling Partselect.com was quick and easy. I know I sond like a late night comercial but I will use them again for my next home repair!
Ted Lamarche

put new hose on, very easy.

PartSelect found the right part for me on the first try. I had scoured the web looking for this particular drying agent cap. Even Sears said I'd have to order the entire dispenser assembly - $$$!

PartSelect found just the cap I needed at a much better price.

Fantastic service. Shipping was faster than promised. I can't say enough good things about them!

Start Button on top was worn away and the contact below was no longer starting the dishwasher. Removed the Torx screws holding the latch then the remaining holding the outer door, be careful it can be a touch heavy and bulky. disconnected the wiring harness from the door to the (computer) you might want to mark the positions of the 4 blade type wires as the connections are the same size.. take a picture before you start removal, or use a bit of tape. Once wires are removed, use a jewelers or very small blade screwdriver to separate the wiring from the control panel from the computer, it is easier if you do this while it is still in the plastic housing as it can be a bit tight to remove then simply push back the retainers, not much force is needed, if you look closely you can see where the (teeth) hold the computer and old control board down. Once you have separated the control board and the computer from the housing, install the control board, with the switches aligned under the contact buttons, and clip it into place, then the computer and the wiring to the control board.. then connect back to dishwasher, and reinstall the door, You may want to have someone assist in holding the door in place and lightly install the center screws, then the bottoms before the upper ones, after all are aligned and started then go back and tighten all screws, remember, you don't need to over tighten them. once replaced, test and and start. It is easy I was quoted over $400 for this job.. I bought the parts for $200 and saved $200. Good Luck.