KUDA23SYWH0 KitchenAid Dishwasher - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Steven from Norton, MA
- Parts Used:
- 4171544
- Difficulty Level:
- Easy
- Total Repair Time:
- Less than 15 mins
Glasses on top rack of the dishwasher had soap film on the inside. The rubber distribution hose under the top rack had rotted and split. Didn't see it right away because it split on the bottom.
Part was easy to locate on the website. Photo on the measurement grid was the key after entering the maker and model number. I have found refrigerator parts the same way on this site. Sliced the old rotten hose to remove it. The new hose only had to be slipped over the connections. I soaped the ends of the tube to make the installation easier.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Madolyn from Elkmont, AL
- Parts Used:
- 4171544
- Difficulty Level:
- Easy
- Total Repair Time:
- Less than 15 mins
Rubber water tube had worn out.
I just slipped the old, worn out tube off, warmed the new one in some hot water for a few minutes to make it more pliable, sprayed some non-stick spray on the end connecting in the back, and slipped it on. Piece of cake!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- ELLEN from TUSCALOOSA, AL
- Parts Used:
- WP4162322
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
dishwasher rack rusted
It was easy to remove rack from dishwasher. I screwed on rollers and it was like new!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Gerald from Woodburn, OR
- Parts Used:
- 4171544
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Hose was worn out, had holes in it.
First removed old hose from the upper rack. Used hair dryer to heat the hose up ( hose was a little stiff) and installed hose. It's pretty simple to install, I didn't even have to unload the dishwasher
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Sherry from Hollywood, FL
- Parts Used:
- 4162321
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Pliers
3 roller axles were broken on bottom dishwasher rack.
I pulled off the broken parts and snapped on the new axles, then replaced the wheels. Very simple.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Veronica from Richmond, VA
- Parts Used:
- 4171544
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Rubber Water Tube disintegrated from age
The whole operation took about 5 minutes which included opening the package! Sprayed some vegetable spray inside the opening of the water tube that attached to the spray connection and it slipped right on. Absolutely amazing and I feel like I have a brand new dishwater! My dishes are definitely cleaner too! Thank you Parts Select for posting how to instructions!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Elmer from YORKVILLE, IL
- Parts Used:
- 675806
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 1- 2 hours
1/4 inch bolt frozen to shaft
The 1/4 inch impeller bolt to shaft would not budge with a nut driver so I had to use a ratchet to loosen it. I could not hold the drain impeller with an adjustable wrench so I had to use a vice-grip. This still did not loosen it so I used an oscillating power saw to cut away at the bottom of the drain impeller being careful to only cut so deep, I didn't want to cut into the motor shaft. Once I had cut some grooves into the drain impeller, I could break it into pieces and remove it. Upon reassembly I tightened the 1/4 inch bolt with the ratchet.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Michael from buffalo, NY
- Parts Used:
- 4171544
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
upper rack propeller jets lost power
I removed the old, brittle and leaky water delivery tube by hand and at the outlet and at the inlet end, by cutting it away with an exacto knife. I then heated the new tube under hot water and coated each end with dishwasher soap. With only a modest amount of manipulation, both ends slipped easily into place and the hose was immediately secure and operable. My wife, who didn't witness my efforts, thought I was a genius.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Rene from New Berlin, WI
- Parts Used:
- 4171544
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Rubber Water Delivery Tube had decayed over time.
Manually remove old tube and simply replace with new tube - no tools!
Was this instruction helpful to you?
Thank you for voting!
Missing Items
Simply replaced the wheels/axiles and brackets using functioning ones as template. No problem at all.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- michael from topeka, KS
- Parts Used:
- 4162321
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
roller axle broken, roller fell off
first-removed all axles from one side of rack. replace with new ones, replace rollers. repeat for other side of rack. VIOLA!!
Was this instruction helpful to you?
Thank you for voting!
Rollers came off my bottom rack due to broken axles.
I ordered all new axles even though not all of them were broken - I figured it was just a matter of time. Ordered one new roller because one was missing, and an extra one just in case. Removed all old rollers and axles. A couple of them did not want to come off, so I "hit" them with a screwdriver. Put on all new axles and replaced the rollers. The whole project took about 10 minutes. SUPER EASY. CHEAP FIX FOR MY OLD DISHWASHER.
Was this instruction helpful to you?
Thank you for voting!
Mom died, selling her house. lower rack of dishwasher with only 2 out of 8 wheels
The website had great pictures, I compared the wheels I had and the broken axles with the pictures, and picked what I thought would match. They were perfect. I used pliers to pop the axle on, and my fingers to put on the wheels. It works perfectly now
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Walter from KINGSPORT, TN
- Parts Used:
- 675806
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 1- 2 hours
- Tools:
- Nutdriver, Screw drivers, Socket set, Wrench (Adjustable)
i had a leak under the dishwasher when the pump turned on.
I replaced the seals per the video instructions.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Anita from CAPE MAY, NJ
- Parts Used:
- WP4172117
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Replacement for rusting 40 yr old rack
Tranfered wheels from old rack to replacement rack. Silverware caddy was a bit too big for the replacement. I gently bent the prongs on the rack a little and its fits perfect.
Was this instruction helpful to you?
Thank you for voting!