KUDI22HT0 KitchenAid Dishwasher - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Daniel from Nine Mile Falls, WA
- Parts Used:
- 4171544
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Worn out water tube.
Took old one off and put new one on, about a 4 minute job.
The part was about 1/3 of the cost if I had bought it local.
The part was about 1/3 of the cost if I had bought it local.
Was this instruction helpful to you?
Thank you for voting!
Tube cracked and split
Pulled off old tube and upper arm receiver.The new tube and the section it was to go on appeared to be too small. I heated new tube with hair blower and streched new tube so as to fit .
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Howard from Boynton Beach, FL
- Parts Used:
- 350930
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver
Both outside door handles turned very beige
Everything worked perfectly---thanks to the suggestion of your call center agent. She suggested that since the replacement door handles were no longer available, I should consider repainting them--it worked like a charm. Please tell her she was a life saver. We rent that house in Fl and my returning tenants had complained about the discoloring refer handles. Thank you
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Corinne from El Granada, CA
- Parts Used:
- 4171544
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 15 - 30 mins
Old water tube had worn through and was falling off.
Removed old water tube and replaced it with the new one. Hard part was logistically trying to put it below the rack and it obviously it had to fit very tight and it was quite difficult to get in place, but I did it! Thanks to your easy to use website and excellent service. I was proud of myself for doing the whole job start to finish, and my husband was even more impressed. Only downside to that is that I think he'll be playing more golf, while I do the repair work from now on.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Robert from Ringle, WI
- Parts Used:
- 4163050
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 1- 2 hours
- Tools:
- Screw drivers
Dishwasher wouldn't drain.
After checking for blockages in the drain line and finding none, I disassembled the wash wand assembly and discovered a gasket that had really deteriorated. Since there was nothing else apparently wrong, I took a chance and went shopping for the gasket. None of my local stores could provided me one so I searched on line and found it at Partselect. It had to be special ordered and that took a while, but when it arrived, I put the new gasket in and had a perfect dishwasher again for less than 15 bucks. The schematic I was able to print from your website was invaluable.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Brian from Davis, CA
- Parts Used:
- WP4171000
- Difficulty Level:
- Easy
- Total Repair Time:
- 1- 2 hours
- Tools:
- Nutdriver, Pliers, Wrench (Adjustable), Wrench set
Dishes not getting clean.
I was trying to avoid having to buy a new dishwasher before the holidays. I went on YouTube and found the dirty dishes may mean bad water inlet valve. So, I used my meter to see if the valve was bad and sure enough it was. I ordered the part from Part Select. Once I received the part I removed the old one. Be sure to put a towel down to catch the excess water. The bracket that came with the new prt was a different configuration, but i swapped the new with old and it worked. I addition to the valve being bad the dishwasher upper and lower arms were somewhat clogged. I looked online again and followed YouTube instructions to clean. The dishwasher is cleaning like it is new. I would recommend to anyone doing work on their dishwasher to use part select and thoroughly clean the upper and lower arm.
Was this instruction helpful to you?
Thank you for voting!
Roller axles dried out and brittle and broke
Removed bottom rack and replaced axles and wheels, works just like new and did it without any assistance from my son or Husband.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Debra from Windham, CT
- Parts Used:
- 4171544
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
hose had blown a hole
just popped the old hose off and put the new one on. the part was shipped very quickly and I received it within a week even during the holidays
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Alan from Spooner, WI
- Parts Used:
- 4171544
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
water tube split and fell on drying element
Removed old tube, moistened both ends of new tube with hot water and slid over inlet and outlet holes. Repair done!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Robert from Powell, OH
- Parts Used:
- 4171544
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
The rubber tube for the top rack was rotted in half, not allowing the dishes to properly be cleaned.
First the water tube arrived two days earlier than what I was expecting. I pulled the old tube off and slipped the new tube on by hand. The dishes in the top rack are now a lot cleaner than they have been for the past couple of months. In the future if I need repair parts this is where I will be coming to get them.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Janice from Napa, CA
- Parts Used:
- 4171544
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Dishwasher not cleaning as rubbr water tube cracked
I removed clips on the end of the rack, removed the rack, and pulled old tube off. Used plain water as a lubricant to ease replacement of new tube on the dilated end. Very easy!
Was this instruction helpful to you?
Thank you for voting!
Water tube rotted out and support cracked, no water going to top rack of dishwasher.
Pulled off old tube, applied small amount of lubricant to each end of tube, then just pushed ends together. Slide right on, attached new support and in less then five minutes, fixed. Dishwasher running like new.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Stephanie from Rye, NY
- Parts Used:
- 4171544
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
hose had a hole and was rotting
I pulled out the old hose and pushed in the new one. Took a little muscle, but was glad that it fit. On line site very helpful with description so that it fit perfectly!
Was this instruction helpful to you?
Thank you for voting!
wheels and axles had broken off rack - not able to slide in/out smoothly anymore
Simply popped on new axles and wheels and dishwasher works like new!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Edward from Winchester, MA
- Parts Used:
- 4171544
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
Tude was disintegrating.
Removed old tube.
New tube was a little tight, so I heated it with a hair dryer and used dish washing detergent - Joy - as a lubricant. Then the tube slipped on easily.
New tube was a little tight, so I heated it with a hair dryer and used dish washing detergent - Joy - as a lubricant. Then the tube slipped on easily.
Was this instruction helpful to you?
Thank you for voting!