KUDP22ST3 KitchenAid Dishwasher - Instructions

first-removed all axles from one side of rack. replace with new ones, replace rollers. repeat for other side of rack. VIOLA!!

I ordered all new axles even though not all of them were broken - I figured it was just a matter of time. Ordered one new roller because one was missing, and an extra one just in case. Removed all old rollers and axles. A couple of them did not want to come off, so I "hit" them with a screwdriver. Put on all new axles and replaced the rollers. The whole project took about 10 minutes. SUPER EASY. CHEAP FIX FOR MY OLD DISHWASHER.

The website had great pictures, I compared the wheels I had and the broken axles with the pictures, and picked what I thought would match. They were perfect. I used pliers to pop the axle on, and my fingers to put on the wheels. It works perfectly now

I took out the bottom rack, turned it upside down, popped off the wheels and saved them and put on the new axles. It took a little doing to get the new axles snapped into place-they were stiff. I finally figured out how to use the pliers at the right angle to pop them on. Then the wheels popped right on and off I went.

Like the video showed but very hard to stretch tube over wider part on interior of top shelf. Read afterwards that hair dryer would have helped. Video should mention that. Bruised hands and wrists getting it on good.

we used hot water to soften the ends of the tube and then slid it onto the two ends of the parts in the dishwasher. It did take a little bit of "push" to get it on one end, but nothing we could not handle. I would say anyone with common sense and willingness to fix something them selves would have no problem. I would like to say the part I ordered was of good quality and saved me a lot of money.

removed screws from dishwasher and discovered i could replace panel because of door type

Removed the old axles and rollers and snapped in the new ones. Really easy repair.

Finally listened to advice of others online and decided to replace inlet valve. Btw, the problem is NOT the inlet screen. It was completely clean in my case. Issue is with internal seals that swell over time and restrict flow leading to low water level.

Unplugged unit, removed lower front panel (two screws on outside upper corners), undid compression fitting on inlet supply line, removed two screws holding valve bracket to frame, disconnected electrical connections to valve, used pliers to compress hose clamp to remove valve outlet hose, used adjustable wrench and some elbow grease to remove small inlet elbow (its on tight!) from valve inlet, put teflon tape on elbow threads to reinstall on new valve, reverse removal instructions to put everything back. All done! MUCH cleaner dishes!

First I had to buy a new tray. I tried to remove the wheels from the old tray but they wouldn't come off without breaking. I ordered new wheels and axels and they went on fine with the aid of a C-clamp. Then I tried to remove the old bumpers but they broke when I tried to remove them.
So, I ordered two new bumpers. When I did I saw that another user had posted a note saying that the new bumpers slipped on well if heated in hot water first. So, I heated them in hot water and they slipped on easily and safely.

Very easily!! I am 19 years old and repaired the dishwasher for my grandmother in about 15 minutes. Great products.

I removed the broken axle with the help of a small screwdriver and replaced it with a new one. Then I installed a new roller, which was easy because all I had to do was push it on with my fingers.

One of the easiest repairs I've ever made on anything and now I'm happy because my wife is happy!

After checking for blockages in the drain line and finding none, I disassembled the wash wand assembly and discovered a gasket that had really deteriorated. Since there was nothing else apparently wrong, I took a chance and went shopping for the gasket. None of my local stores could provided me one so I searched on line and found it at Partselect. It had to be special ordered and that took a while, but when it arrived, I put the new gasket in and had a perfect dishwasher again for less than 15 bucks. The schematic I was able to print from your website was invaluable.

I was trying to avoid having to buy a new dishwasher before the holidays. I went on YouTube and found the dirty dishes may mean bad water inlet valve. So, I used my meter to see if the valve was bad and sure enough it was. I ordered the part from Part Select. Once I received the part I removed the old one. Be sure to put a towel down to catch the excess water. The bracket that came with the new prt was a different configuration, but i swapped the new with old and it worked. I addition to the valve being bad the dishwasher upper and lower arms were somewhat clogged. I looked online again and followed YouTube instructions to clean. The dishwasher is cleaning like it is new. I would recommend to anyone doing work on their dishwasher to use part select and thoroughly clean the upper and lower arm.

Repair was fairly easy, had to swith the mounting bracket from the old valve no problem. Install reconnected the water and the dishwasher works great now!