KPDI620T5 KitchenAid Dishwasher - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
roller wheels & axles broken
Old roller wheels and axles were broken and already falling off. I simply replaced the roller axles and snapped on the new roller wheels.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- James from Midlothian, VA
- Parts Used:
- 4171544
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
The old rubber water tube had dry-rotted
Simply inserted the new rubber hose on the two fittings - a couple of minutes at most
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- milka from brooklyn, NY
- Parts Used:
- 4171544
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
dishwasher had smoke
it was a very easy repair thank you
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- anne from clinton, MS
- Parts Used:
- 4171544
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Rubber Hose Had Holes In Itt
I heated both ends of rubber hose and applied a small amount of vaseline inside of tube and it slid on real easy. It took less than 5 minutes to finish the task.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Bill from Chelan, WA
- Parts Used:
- 4171544
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
The old peice was wore out and had holes and kept falling off.
I just put 1 drop of hand soap in each end of the new hose , that let it slide on EZ.
Was this instruction helpful to you?
Thank you for voting!
old part corroded and fell off
This was sooo easy. The key was the "tip" on this website to lubricate the parts with dish soap. They slid right on. It works perfectly. Most important, I am a Hero with the wife ... that gets special rewards!!
Was this instruction helpful to you?
Thank you for voting!
Axles on lower rack broken
Very, very simple. The axles are nylon plastic and snap into the plastic-coated metal grid that forms the lower dishwasher rack. Over time they get brittle and break.
Replacement consists of snapping the old axle out of the rack and snapping the new one in. I replaced some of the wheels at the same time, as we had lost them. The wheels don't seem to wear out, so if you did this repair in time, you could re-use the wheels.
These little axles are EXPENSIVE ($3.50 each!), but for $30 you can replace all eight of them, and your dishwasher rack will work like new again!
Replacement consists of snapping the old axle out of the rack and snapping the new one in. I replaced some of the wheels at the same time, as we had lost them. The wheels don't seem to wear out, so if you did this repair in time, you could re-use the wheels.
These little axles are EXPENSIVE ($3.50 each!), but for $30 you can replace all eight of them, and your dishwasher rack will work like new again!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Barbara from Santa Rosa Beach, FL
- Parts Used:
- 4171544
- Difficulty Level:
- Easy
- Total Repair Time:
- Less than 15 mins
The old tube was worn out and had holes
Took the old one off then used canola oil to put on the inside of the tube and it went on easy.
Was this instruction helpful to you?
Thank you for voting!
A roller came off the bottom washer tray in the dishwasher because of broken axle
I removed the broken axle with the help of a small screwdriver and replaced it with a new one. Then I installed a new roller, which was easy because all I had to do was push it on with my fingers.
One of the easiest repairs I've ever made on anything and now I'm happy because my wife is happy!
One of the easiest repairs I've ever made on anything and now I'm happy because my wife is happy!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Daniel from Lorain, OH
- Parts Used:
- 4171544
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Worn out rubber delivery tube
Slipped old one off slid new one on . Took about one minute. Held well and is washing so much better now.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- robert from glenmoore, PA
- Parts Used:
- 4171544
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
worn rubber tube water feed to upper spin arm in dishwasher
The replacement worked fine, but the website could have been a bit more re-assuring in terms of showing the image of the part. It was not possible on the website to determine whether the piece was going to fit, as the piece as shown was flat/oval on both ends, where the fitting for the water feed is round. The site could have explained that this was flexible material that would form itself to the round feed connection. The measurements of the part should also be given. The price was right, so I bought it anyway, and hoped. As I have said, it DID work fine. You need to clarify the item on the website.
Was this instruction helpful to you?
Thank you for voting!
Roller axles dried out and brittle and broke
Removed bottom rack and replaced axles and wheels, works just like new and did it without any assistance from my son or Husband.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Corinne from El Granada, CA
- Parts Used:
- 4171544
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 15 - 30 mins
Old water tube had worn through and was falling off.
Removed old water tube and replaced it with the new one. Hard part was logistically trying to put it below the rack and it obviously it had to fit very tight and it was quite difficult to get in place, but I did it! Thanks to your easy to use website and excellent service. I was proud of myself for doing the whole job start to finish, and my husband was even more impressed. Only downside to that is that I think he'll be playing more golf, while I do the repair work from now on.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- DANNY from MORONGO VALLEY, CA
- Parts Used:
- WP4171000
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Pliers, Screw drivers
No Water Coming Into Dishwasher
Repair was fairly easy, had to swith the mounting bracket from the old valve no problem. Install reconnected the water and the dishwasher works great now!
Was this instruction helpful to you?
Thank you for voting!
Rollers and axels were worn out.
Very easily!! I am 19 years old and repaired the dishwasher for my grandmother in about 15 minutes. Great products.
Was this instruction helpful to you?
Thank you for voting!