4KUDP220T1 KitchenAid Dishwasher - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Allen from MOUNT VERNON, WA
- Parts Used:
- WP4160355
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
Replacing broken door hinge guide bearing sleeve
Repair was awful without instructions. Instructions were requested twice with no response. Attempted without instruction and broke the sleeve. Reordered but not through Partselect
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Judy from SCRANTON, PA
- Parts Used:
- WP4171544
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
Dry rotted water delivery tube
I put a whirlpool tube on my Jen more dishwasher . Fits like a glove.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Linda from GARLAND, TX
- Parts Used:
- WP4171544
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
water delivery tube had rotted over time
followed the tutorial video and just removed the old one and the new one slipped right on.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Anita from CAPE MAY, NJ
- Parts Used:
- WP4172117
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Replacement for rusting 40 yr old rack
Tranfered wheels from old rack to replacement rack. Silverware caddy was a bit too big for the replacement. I gently bent the prongs on the rack a little and its fits perfect.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Anne from Sebastopol, CA
- Parts Used:
- 4162321
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Pliers
a couple of axles disintegrated so the bottom dish rack wouldn't roll
I took out the bottom rack, turned it upside down, popped off the wheels and saved them and put on the new axles. It took a little doing to get the new axles snapped into place-they were stiff. I finally figured out how to use the pliers at the right angle to pop them on. Then the wheels popped right on and off I went.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Janice from NEW COLUMBIA, PA
- Parts Used:
- WP4171544
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
water delivery tube was rotted and no longer delivered water to the top arm, so top shelf of dishwasher no longer worked
we used hot water to soften the ends of the tube and then slid it onto the two ends of the parts in the dishwasher. It did take a little bit of "push" to get it on one end, but nothing we could not handle. I would say anyone with common sense and willingness to fix something them selves would have no problem. I would like to say the part I ordered was of good quality and saved me a lot of money.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- robert from cranston, RI
- Parts Used:
- 4169400
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
dishwasher not adaptable for change of panel
removed screws from dishwasher and discovered i could replace panel because of door type
Was this instruction helpful to you?
Thank you for voting!
bottom drawer roller replacement
Removed the old axles and rollers and snapped in the new ones. Really easy repair.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Gerald from Sharon, MA
- Parts Used:
- 4171555
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 30 - 60 mins
Bottom tray of dishwasher started to rust and pins were falling.
First I had to buy a new tray. I tried to remove the wheels from the old tray but they wouldn't come off without breaking. I ordered new wheels and axels and they went on fine with the aid of a C-clamp. Then I tried to remove the old bumpers but they broke when I tried to remove them.
So, I ordered two new bumpers. When I did I saw that another user had posted a note saying that the new bumpers slipped on well if heated in hot water first. So, I heated them in hot water and they slipped on easily and safely.
So, I ordered two new bumpers. When I did I saw that another user had posted a note saying that the new bumpers slipped on well if heated in hot water first. So, I heated them in hot water and they slipped on easily and safely.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Scott from Lake Forest, CA
- Parts Used:
- WP4171000
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Pliers, Screw drivers, Wrench (Adjustable)
Dishes and glasses were not clean - soap residue
Finally listened to advice of others online and decided to replace inlet valve. Btw, the problem is NOT the inlet screen. It was completely clean in my case. Issue is with internal seals that swell over time and restrict flow leading to low water level.
Unplugged unit, removed lower front panel (two screws on outside upper corners), undid compression fitting on inlet supply line, removed two screws holding valve bracket to frame, disconnected electrical connections to valve, used pliers to compress hose clamp to remove valve outlet hose, used adjustable wrench and some elbow grease to remove small inlet elbow (its on tight!) from valve inlet, put teflon tape on elbow threads to reinstall on new valve, reverse removal instructions to put everything back. All done! MUCH cleaner dishes!
Unplugged unit, removed lower front panel (two screws on outside upper corners), undid compression fitting on inlet supply line, removed two screws holding valve bracket to frame, disconnected electrical connections to valve, used pliers to compress hose clamp to remove valve outlet hose, used adjustable wrench and some elbow grease to remove small inlet elbow (its on tight!) from valve inlet, put teflon tape on elbow threads to reinstall on new valve, reverse removal instructions to put everything back. All done! MUCH cleaner dishes!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Howard from Boynton Beach, FL
- Parts Used:
- 350930
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver
Both outside door handles turned very beige
Everything worked perfectly---thanks to the suggestion of your call center agent. She suggested that since the replacement door handles were no longer available, I should consider repainting them--it worked like a charm. Please tell her she was a life saver. We rent that house in Fl and my returning tenants had complained about the discoloring refer handles. Thank you
Was this instruction helpful to you?
Thank you for voting!
Roller axles dried out and brittle and broke
Removed bottom rack and replaced axles and wheels, works just like new and did it without any assistance from my son or Husband.
Was this instruction helpful to you?
Thank you for voting!
Axles on lower rack broken
Very, very simple. The axles are nylon plastic and snap into the plastic-coated metal grid that forms the lower dishwasher rack. Over time they get brittle and break.
Replacement consists of snapping the old axle out of the rack and snapping the new one in. I replaced some of the wheels at the same time, as we had lost them. The wheels don't seem to wear out, so if you did this repair in time, you could re-use the wheels.
These little axles are EXPENSIVE ($3.50 each!), but for $30 you can replace all eight of them, and your dishwasher rack will work like new again!
Replacement consists of snapping the old axle out of the rack and snapping the new one in. I replaced some of the wheels at the same time, as we had lost them. The wheels don't seem to wear out, so if you did this repair in time, you could re-use the wheels.
These little axles are EXPENSIVE ($3.50 each!), but for $30 you can replace all eight of them, and your dishwasher rack will work like new again!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- DANNY from MORONGO VALLEY, CA
- Parts Used:
- WP4171000
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Pliers, Screw drivers
No Water Coming Into Dishwasher
Repair was fairly easy, had to swith the mounting bracket from the old valve no problem. Install reconnected the water and the dishwasher works great now!
Was this instruction helpful to you?
Thank you for voting!
A roller came off the bottom washer tray in the dishwasher because of broken axle
I removed the broken axle with the help of a small screwdriver and replaced it with a new one. Then I installed a new roller, which was easy because all I had to do was push it on with my fingers.
One of the easiest repairs I've ever made on anything and now I'm happy because my wife is happy!
One of the easiest repairs I've ever made on anything and now I'm happy because my wife is happy!
Was this instruction helpful to you?
Thank you for voting!