KUDP22GT2 KitchenAid Dishwasher - Instructions

It was 94 degrees that day so I set the rubber hose outside in the sun to loosen it up, make it more plyable. I then mixed up some soapy water and doused the ends of the hose with the soapy water and slid the hose right onto the fittings.

There was a small hole in the hose which was not discussed in the directions. I assumed the hole should be installed on the down side to let water drain out after the dishwasher is finished. This will reduce the chance of bacteria building in the hose.

I read the installation tips before I started and picked up the soap mix and heating up the hose before installation. Can be accomplished with a hair dryer if it is not 94+ degrees outside!!!

Thanks,

Jim

For several years I endured difficulty in pushing in and pulling out a fully loaded lower dishwasher tray in my KitchenAid Superba dishwasher. The tray would "fall out" out of its "track" and jam requiring me to lift up the whole tray to try to pull it out. Then one of the plastic roller "axles" broke and its wheel fell off. So I went on to Part Select's website to find a replacement. When I got it in the mail I replaced the one that broke. I noticed how much more rigid the wheel then ran on its "track." So I replaced all the roller axles and, lo and behold, the lower tray does not jam anymore. It rolls just like new! I am very satisfied. Chris from Bay Ridge, Brooklyn

Took the tube off and noted that there was a factory drilled hole on the underside that lets water drain. I slipped the new tube over the inlet port and the other end over the rotating washing arm aparatus port and everything worked fine. Very easy and fast repair.

One of the axles broke off, requiring no removal. The other wheel broke off, but the axle remained. That required squeezing (pliers) to push out. Replacement was easy; just put wheel onto axle and push axle through mounting space. Total: 5 minute job.

I heated both ends of rubber hose and applied a small amount of vaseline inside of tube and it slid on real easy. It took less than 5 minutes to finish the task.

I pulled out the old hose and pushed in the new one. Took a little muscle, but was glad that it fit. On line site very helpful with description so that it fit perfectly!

Simply popped on new axles and wheels and dishwasher works like new!

The replacement worked fine, but the website could have been a bit more re-assuring in terms of showing the image of the part. It was not possible on the website to determine whether the piece was going to fit, as the piece as shown was flat/oval on both ends, where the fitting for the water feed is round. The site could have explained that this was flexible material that would form itself to the round feed connection. The measurements of the part should also be given. The price was right, so I bought it anyway, and hoped. As I have said, it DID work fine. You need to clarify the item on the website.

Warm rollers and holders in warm water for 2 min each slide on all done

slid old tube pieces off slid new hose on

I was goingto go to Home-Depot, and purchase a short piece of tubing to make the repair.
Just for the "heck" of it, I looked on-line --- and there it was. It is a large diameter thin wall tube, because water presiue is low, almost zero.
However, the replacement part was only $8,25, so I figured, what the heck, I can wait a few days and purchased the part from PartSelect.com. I lubricated the new tube with soap, to make the slip-fit go on easier and -------------- Done

Very easy ......... Thank you

Old roller wheels and axles were broken and already falling off. I simply replaced the roller axles and snapped on the new roller wheels.

Simply inserted the new rubber hose on the two fittings - a couple of minutes at most

First I pulled off the tube that was hanging down and obstructing the rotation of the top spinner. Then I just reinserted the new tube. I'm a "do it your selfer" and I usually fix things by my self. But the few times that I've failed lived forever in my wife's memory. She dreaded my fooling with a machine that had outlived it's life. I promised that the job would only take about five minutes. She heard this before and resigned herself to having parts all over the kitchen floor and a full day of catastrophe. There is nothing like a satisfied wife.Thanks to You and your Staff, I have now regained my rightful place as her trusted HERO.. ,

I removed the broken axle with the help of a small screwdriver and replaced it with a new one. Then I installed a new roller, which was easy because all I had to do was push it on with my fingers.

One of the easiest repairs I've ever made on anything and now I'm happy because my wife is happy!