KUDS230Y2 KitchenAid Dishwasher - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Elwood from Battlecreek, MI
- Parts Used:
- 4171544
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
the delivery tube was worn out with holes
the tube slid off and I used some liquid soap to spread on the end of each tube and I slid the new tube back on with ease and the upper rack of dishes now get cleaned/rinsed.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Robert from Rancho Plaos Verdis, CA
- Parts Used:
- 4171544
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- Less than 15 mins
The tube on the top split
Our old Kitchenaid Dishwasher was not getting the glasses on the top shelf clean. I looked and found the tube running to the washer arm under the top basket was split.
I replaced the tube. First I put dish soap in the ends of the new tube, so they slipped onto the other parts with only moderate force.
Now the dishwasher is making the glasses in the top basket clean again.
Regards,
Bob
I replaced the tube. First I put dish soap in the ends of the new tube, so they slipped onto the other parts with only moderate force.
Now the dishwasher is making the glasses in the top basket clean again.
Regards,
Bob
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Bill from Chelan, WA
- Parts Used:
- 4171544
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
The old peice was wore out and had holes and kept falling off.
I just put 1 drop of hand soap in each end of the new hose , that let it slide on EZ.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Edward from Winchester, MA
- Parts Used:
- 4171544
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
Tude was disintegrating.
Removed old tube.
New tube was a little tight, so I heated it with a hair dryer and used dish washing detergent - Joy - as a lubricant. Then the tube slipped on easily.
New tube was a little tight, so I heated it with a hair dryer and used dish washing detergent - Joy - as a lubricant. Then the tube slipped on easily.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- robert from glenmoore, PA
- Parts Used:
- 4171544
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
worn rubber tube water feed to upper spin arm in dishwasher
The replacement worked fine, but the website could have been a bit more re-assuring in terms of showing the image of the part. It was not possible on the website to determine whether the piece was going to fit, as the piece as shown was flat/oval on both ends, where the fitting for the water feed is round. The site could have explained that this was flexible material that would form itself to the round feed connection. The measurements of the part should also be given. The price was right, so I bought it anyway, and hoped. As I have said, it DID work fine. You need to clarify the item on the website.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Merdell from Montgomery, TX
- Parts Used:
- 4171544
- Difficulty Level:
- Easy
- Total Repair Time:
- Less than 15 mins
hole in the tube, wear and tear on it
I removed the old tube--I had taped over the hole. I didn't quite have the hand strength to fit over the ends and push the new tube into place. So, my husband did that at both ends without a problem. I'm relying on PartSelect for when I need parts for my 13 year-old appliances.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Catherine from Twin Lakes, WI
- Parts Used:
- 4171544
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Tube to the top rack that supplies water
The tube had holes from being used but the dishwasher still works great. I researched this part and it was a great price and really easy to fix. The picture looks different than what the tube looks like in the dishwasher but it is correct. Definitely put soap on the ends to help glide it on. Took me 2 minutes to fix.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Daniel from Madison, NJ
- Parts Used:
- 4171544
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Upper water tube had a leak
simply pieced together the "tube"
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Scott from Orland Park, IL
- Parts Used:
- 4171544
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Cracked water tube
I was goingto go to Home-Depot, and purchase a short piece of tubing to make the repair.
Just for the "heck" of it, I looked on-line --- and there it was. It is a large diameter thin wall tube, because water presiue is low, almost zero.
However, the replacement part was only $8,25, so I figured, what the heck, I can wait a few days and purchased the part from PartSelect.com. I lubricated the new tube with soap, to make the slip-fit go on easier and -------------- Done
Very easy ......... Thank you
Just for the "heck" of it, I looked on-line --- and there it was. It is a large diameter thin wall tube, because water presiue is low, almost zero.
However, the replacement part was only $8,25, so I figured, what the heck, I can wait a few days and purchased the part from PartSelect.com. I lubricated the new tube with soap, to make the slip-fit go on easier and -------------- Done
Very easy ......... Thank you
Was this instruction helpful to you?
Thank you for voting!
roller wheels & axles broken
Old roller wheels and axles were broken and already falling off. I simply replaced the roller axles and snapped on the new roller wheels.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- James from Midlothian, VA
- Parts Used:
- 4171544
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
The old rubber water tube had dry-rotted
Simply inserted the new rubber hose on the two fittings - a couple of minutes at most
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Murray from Hendrsonville, NC
- Parts Used:
- 4171544
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Rubber tube deteriorated and top rack kept jamming
First I pulled off the tube that was hanging down and obstructing the rotation of the top spinner. Then I just reinserted the new tube. I'm a "do it your selfer" and I usually fix things by my self. But the few times that I've failed lived forever in my wife's memory. She dreaded my fooling with a machine that had outlived it's life. I promised that the job would only take about five minutes. She heard this before and resigned herself to having parts all over the kitchen floor and a full day of catastrophe. There is nothing like a satisfied wife.Thanks to You and your Staff, I have now regained my rightful place as her trusted HERO.. ,
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Debra from Windham, CT
- Parts Used:
- 4171544
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
hose had blown a hole
just popped the old hose off and put the new one on. the part was shipped very quickly and I received it within a week even during the holidays
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Robert from Powell, OH
- Parts Used:
- 4171544
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
The rubber tube for the top rack was rotted in half, not allowing the dishes to properly be cleaned.
First the water tube arrived two days earlier than what I was expecting. I pulled the old tube off and slipped the new tube on by hand. The dishes in the top rack are now a lot cleaner than they have been for the past couple of months. In the future if I need repair parts this is where I will be coming to get them.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Alan from Spooner, WI
- Parts Used:
- 4171544
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
water tube split and fell on drying element
Removed old tube, moistened both ends of new tube with hot water and slid over inlet and outlet holes. Repair done!
Was this instruction helpful to you?
Thank you for voting!