KUDJ23HY2 KitchenAid Dishwasher - Instructions

I removed the upper rack from the dishwasher by popping the two rack track stops out of the rack tracks. The old tube came off easily, and the new tube went on very nicely, after lubing each end with a dab of liquid dish soap. I put the rack back on its tracks , popped the track stops back in and my dishwasher was back in business.

The tube had holes from being used but the dishwasher still works great. I researched this part and it was a great price and really easy to fix. The picture looks different than what the tube looks like in the dishwasher but it is correct. Definitely put soap on the ends to help glide it on. Took me 2 minutes to fix.

First the water tube arrived two days earlier than what I was expecting. I pulled the old tube off and slipped the new tube on by hand. The dishes in the top rack are now a lot cleaner than they have been for the past couple of months. In the future if I need repair parts this is where I will be coming to get them.

Slipped old one off slid new one on . Took about one minute. Held well and is washing so much better now.

The replacement worked fine, but the website could have been a bit more re-assuring in terms of showing the image of the part. It was not possible on the website to determine whether the piece was going to fit, as the piece as shown was flat/oval on both ends, where the fitting for the water feed is round. The site could have explained that this was flexible material that would form itself to the round feed connection. The measurements of the part should also be given. The price was right, so I bought it anyway, and hoped. As I have said, it DID work fine. You need to clarify the item on the website.

I removed the roll out top wire rack of the dishwasher, turned it over and pulled the old punctured water supply tube off the force fit connectors on each end. I put a small amount of vaseline lubricant immediately inside the mouth of the new tube at each end. I pressed the ends of the new tube over the force fit connectors and tested them by shaking the pipe. I replaced the rack and fastened it into place.

For several years I endured difficulty in pushing in and pulling out a fully loaded lower dishwasher tray in my KitchenAid Superba dishwasher. The tray would "fall out" out of its "track" and jam requiring me to lift up the whole tray to try to pull it out. Then one of the plastic roller "axles" broke and its wheel fell off. So I went on to Part Select's website to find a replacement. When I got it in the mail I replaced the one that broke. I noticed how much more rigid the wheel then ran on its "track." So I replaced all the roller axles and, lo and behold, the lower tray does not jam anymore. It rolls just like new! I am very satisfied. Chris from Bay Ridge, Brooklyn

Took the tube off and noted that there was a factory drilled hole on the underside that lets water drain. I slipped the new tube over the inlet port and the other end over the rotating washing arm aparatus port and everything worked fine. Very easy and fast repair.

the tube slid off and I used some liquid soap to spread on the end of each tube and I slid the new tube back on with ease and the upper rack of dishes now get cleaned/rinsed.

I ordered the part and I received it in just 2 days. I took the old rubber water tube off, put a little soap on each end of the new tube and had it in in under 10 minutes. I am a woman in her 60's and I did this myself!

First I pulled off the tube that was hanging down and obstructing the rotation of the top spinner. Then I just reinserted the new tube. I'm a "do it your selfer" and I usually fix things by my self. But the few times that I've failed lived forever in my wife's memory. She dreaded my fooling with a machine that had outlived it's life. I promised that the job would only take about five minutes. She heard this before and resigned herself to having parts all over the kitchen floor and a full day of catastrophe. There is nothing like a satisfied wife.Thanks to You and your Staff, I have now regained my rightful place as her trusted HERO.. ,

Old tube was falling off, but new one was really easy to install. Put a little soap on the inside as a lubricant. I was thrilled with this; the website was really easy to navigate. Found the part I needed in minutes & the part came very quickly. Thanks!

The tube had a huge hole in it. It was very easy to replace - I just pulled off the old one and put on the new. The cool thing was how easy it was to find the exact part I needed online in less than 5 minutes. Gotta love the internet!

I was goingto go to Home-Depot, and purchase a short piece of tubing to make the repair.
Just for the "heck" of it, I looked on-line --- and there it was. It is a large diameter thin wall tube, because water presiue is low, almost zero.
However, the replacement part was only $8,25, so I figured, what the heck, I can wait a few days and purchased the part from PartSelect.com. I lubricated the new tube with soap, to make the slip-fit go on easier and -------------- Done

Very easy ......... Thank you

Old roller wheels and axles were broken and already falling off. I simply replaced the roller axles and snapped on the new roller wheels.