KUDP01DLBL6 KitchenAid Dishwasher - Instructions

First: Turn power to the Dish washer OFF, then remove the two panels at the bottom of the dishwasher.
Two: remove the Door face panel for easier access to the inlet-Valve.
Three: remove screw that holds Inlet-valve bracket.
Four: slide Inlet valve bracket left and back to get out of slots.
Five: Holding the Inlet-valve forward loosen and remove water line (copper tube nut / pressure fitting).
Six: Remove two wire clips
Seven: Remove platics hose (Spring Clamp)
Replace Inlet-Valve and reverse process///

Started as dishes not getting clean and I observed that the top arm was not spinning and there was very low water pressure coming out of the jets. After making sure the water level was up to the bottom of the heating element and making sure the jets were not clogged I checked the filter and chopper. It was a little tough to get the cover off of the chopper but once I did I could see that the chopper scraper was broken off and the shaft was broken. The screen was all clogged up with stuff. Ordered a new assembly and put it in making sure to compress the spring and make sure the gears lined up. Now it is running great.
I think the Kitchenaid is the same as the Whirlpools.

Got Maintenance Flyer out an read about problem
Removed access plate
Disconnectd water and drain
Removed anchor screws
Pulled unit out and disconnedted from Electric
Flipped on it's back
Ohmed out all heat related items and found discrepency with Thermisitor resistance
Ordered and received Part
Changed out Thermisitor
Checked wiring to Heater and replaced connections
Hooked electric up
Ran Diognostics per Maintenance flyer and cleared fault
Hooked back up and ran like a champ

The reason it took so long is because I put the old thermisitor back in and tryed to run the diognostics just to make sure that was the problem

I watched the instructional videos that showed how to replace the inlet fill hose/water inlet a couple of times. The repair was exactly as shown. No trouble at all.

Turned off water and disconnected line, then disconnected drain, turned off power and slid dishwasher out and turned turned upside down and removed hold down bolt ( it is a 3/8 head bolt) removed wire from motor and twisted motor assembly approximately 1/4 turn counter clock wise and removed old motor and seal assembly reinstalled new motor with new seal and rewired. Turned washer back upright and removed filter assembly and lower jet arm, removed cover for food disposal and reinstalled disposal blade back on pump drive reinstalled cover and filter assembly and jet arm. Slid unit back in place and anchored down to cabinet and turned water and power back on ran washer through a short cycle to clean any soap build up that was left inside and that was it, it all works just like new.

Via your web-site I was able to download the step-by-step screen-shot pictures. I was really surprised on how easy the detailed photo screen shots made the repair really easy! Thanks for making this repair a piece of cake. If I should ever need additional parts for any of my home appliances I will certainly order my parts through PartSelect.

Replaced electronic control panel first which had an obvious defect (burned terminal). Still no power. Replaced fuse and works fine now. Took lots of reading to find out the dishwasher had a replacable fuse. Even the appliance store didn't know.

This product comes in a bottle with a brush like Liquid Paper. It goes on incredibly easy. A second coat might be needed. I wanted to prevent rust from setting in so I covered the scratches and dings. The paint is a little brighter since my washer is 10 years old but it still looks great.

The cycle select buttons on the top of the door worked and would light, however, the power button did not function and did not light. The faulty part ended up not being the control board but the control panel, which included the power button. I spent a good amount of time troubleshooting the problem until I figured this out. The part number was (8531257) Panel-cntl.

Thanks to the previous review of this part, I was able to figure out how to do the replacement myself and saving $150 on a service call. The part is super easy to replace. Remove the screws on the door, lift the outside piece of the door up and off the hinges and then unplug the old piece. I had turned off the electricity to the dishwasher to avoid getting shocked. There were 4 hex nut screws holding the part in, removed those & popped out the old part. Installed the new one, put the door back on and the screws, turned it on and no leaks. This part was so easy to replace, even for a 52 year old woman like myself!

It was easy! First I ordered the expensive replacement parts on line. The parts arrived in one week. I was able to slide the old drawers out, slip a few parts off of the old drawers, snap them on and slide the new drawers in place!

I had to getto the side of the machine. After that, it was simply removing 4 screws and removing the old part, replacing the screws and putting the rack back in the track.

I had no lights on the console. Found the internal fuse blown, as I was looking around noticed the door latch also broken so I replaced that as well. Items were easy to identify from the bom and repairs completed in about 15-20 minutes. Dishes all clean now.

I cleaned the chopper and screen a few times and it continued to get blocked after a couple of cycles. Replaced the chopper assembly and now it works find.

I had a repair guide for my dishwasher which helped. First I removed the water distribution system inside the dishwasher and then removed the door panel. Next I removed the front bottom access panel. I placed a pan under the pump and hoses to catch water when I removed the outlet hose. Very important here! One must remove the pressure switch from the outlet port or else you can't get the pump clear of the washer tub. Next I removed the drain pump by releasing the catch and turning the pump counter clockwise. Now for one of the hard steps. I had to remove three pins which hold the pump assy to the wash tub. Two of them are out of sight so you have to weave you hand past all the hardware and "feel" for the back two. At this point the pump assy just lifts out. Remove the motor /pump by removing one bolt and turning it counter clockwise and withdrawing. I put the new one in. Don't forget to put the pump screen in as I missed this and had to redo the job. Reverse all the previous steps being careful to keep the motor guard out of the pump seal area. Use lots of silicon seal grease and check for leaks on first power up. It took me a couple of adjustments to get a leak-free seal.