4KUDP220T0 KitchenAid Dishwasher - Instructions

Fairly simple to replace the valve. Water input side was a rubber hose that required pliers to squeeze the ring seal and slide it down the hose. Copper pipe on the output side was attached with a 3/8 compression fitting.

I did need to transfer a brass elbow from the old part to the new one.

I unscrewed the screws and slid the panels in. Very easy. I wanted all the appliances to have a stainless steel look.

Snapped in new ones (8) by hand. I was amazed
how fast I was able to find this part online and the
ordering was easy and in a few days the parts
arrived. No hassle trying to explain to anyone what
part I needed. There were pictures of all parts
available. Ordering online, especially if you
know what you are looking for, is really the way to go.

I just pulled out the rack and removed the eight existing roller wheels and roller axles. I was able to remove most of the roller axles with my fingers but needed pliers to remove a couple of them. I then snapped the new roller axles onto the rack and then the roller wheels onto the new roller axles and put the entire rack back in the dishwasher.
The lower rack now rolls smoothly and consistently no matter how many dishes we have piled into it. Also, it has not come off the tracks since replacing the roller axles and roller wheels.

I pulled off the broken parts and snapped on the new axles, then replaced the wheels. Very simple.

i pulled the rack out, took off the old parts then added the new ones. it was quick and simple. i needed no tools and my package of parts arrived quicker than i thought. thanks!

I ordered 8 new axles and used old wheels. I broke off the remaining axle parts left on the wire lower basket with just my hands, and then popped on the new axles. This was done without tools; just needed significant pressure to pop the axles onto the coated wire. The wheels popped onto the axles with a little pressure. Make sure you have the right side of the wheel out. I simply looked at the remaining working wheels before install began to make sure which side goes out. Very easy install.

It was easy to remove rack from dishwasher. I screwed on rollers and it was like new!

We have a remote cottage in Canada with a dishwasher over 30 years old. Since you have to get there by boat we didn't want to have to get a whole new dishwasher installed. The plastic rollers from the top shelf had fallen apart and the top rack would fall off all the time. My daughter found your company online and ordered the exact parts for me! I couldn't believe it. For about $20.00 my dishwasher was fixed by my husband in less than a half hour. It was easy to order the parts from you, they were shipped immediately and worked perfectly. Thank you so much for your help with our dishwasher parts. I was laughed out of Lowe's, Home Depot, Sears and H.H. Gregg when I took my old parts there looking for help with replacement parts. I would recommend your company to everyone.

Repair was awful without instructions. Instructions were requested twice with no response. Attempted without instruction and broke the sleeve. Reordered but not through Partselect

ReplacING the tube was not a big job but the old tube had come apart and pieces had lodged in the sprayer arm. I used a toothpick and nut pick to dislodge the pieces and restore full water flow.

Closed water supply--Turned circuit breaker off to dishwasher--removed lower panel on dishwasher--removed the two wires from water inlet valve--disconnected water supply line--removed angle fitting from old valve & installed in new valve--reinstalled new valve & connected water line & 2 wires--This fixed problem.
I ordered part 11:00 1/15/09--Recd. new one 10:30 next morning. VERY FINE SERVICE & PRICE from PARTS SELECT.COM--Thanks.

I put a whirlpool tube on my Jen more dishwasher . Fits like a glove.

followed the tutorial video and just removed the old one and the new one slipped right on.

Tranfered wheels from old rack to replacement rack. Silverware caddy was a bit too big for the replacement. I gently bent the prongs on the rack a little and its fits perfect.