KUDA23HB0 KitchenAid Dishwasher - Instructions

Used screwdriver to pry off other end of water tube. Kind of cooked on over the years and rear connection point is on a part that is not real strong so you have to be careful to not break or bend the connection. New tube is very tight to get on so putting it on required using the blade of the screwdriver to get the tube to streatch over the two connection points, but not real difficult. Now it's good as new!

I just slipped the old, worn out tube off, warmed the new one in some hot water for a few minutes to make it more pliable, sprayed some non-stick spray on the end connecting in the back, and slipped it on. Piece of cake!

It was easy to remove rack from dishwasher. I screwed on rollers and it was like new!

First removed old hose from the upper rack. Used hair dryer to heat the hose up ( hose was a little stiff) and installed hose. It's pretty simple to install, I didn't even have to unload the dishwasher

The 1/4 inch impeller bolt to shaft would not budge with a nut driver so I had to use a ratchet to loosen it. I could not hold the drain impeller with an adjustable wrench so I had to use a vice-grip. This still did not loosen it so I used an oscillating power saw to cut away at the bottom of the drain impeller being careful to only cut so deep, I didn't want to cut into the motor shaft. Once I had cut some grooves into the drain impeller, I could break it into pieces and remove it. Upon reassembly I tightened the 1/4 inch bolt with the ratchet.

I pulled off the broken parts and snapped on the new axles, then replaced the wheels. Very simple.

The water inlet valve SEEMED to be the logical choice of the part that went bad. It was! It was a really easy fix. Undo the bottom front of the dishwasher. Shut off the hot water supply. Unscrew the hot water pipe leading to the valve. Unscrew the 2 screws holding the vlave to the dishwasher. Unclamp the rubber hose on the other side of the valve leading TO the inside of the dishwasher (water outlet side of the valve) And remove the electrical plug on the old valve. Only time consuming part was the need to remove the male/female coppper fitting from the old valve, put it on the new one and reattach the hotwater pipe....don't forget the teflon tape on the threads, the elecrtrical plug, the rubber hose and the front of the case . My wife says it runs like new

Manually remove old tube and simply replace with new tube - no tools!

I removed the old, brittle and leaky water delivery tube by hand and at the outlet and at the inlet end, by cutting it away with an exacto knife. I then heated the new tube under hot water and coated each end with dishwasher soap. With only a modest amount of manipulation, both ends slipped easily into place and the hose was immediately secure and operable. My wife, who didn't witness my efforts, thought I was a genius.

I replaced the seals per the video instructions.

Simply replaced the wheels/axiles and brackets using functioning ones as template. No problem at all.

I ordered all new axles even though not all of them were broken - I figured it was just a matter of time. Ordered one new roller because one was missing, and an extra one just in case. Removed all old rollers and axles. A couple of them did not want to come off, so I "hit" them with a screwdriver. Put on all new axles and replaced the rollers. The whole project took about 10 minutes. SUPER EASY. CHEAP FIX FOR MY OLD DISHWASHER.

The website had great pictures, I compared the wheels I had and the broken axles with the pictures, and picked what I thought would match. They were perfect. I used pliers to pop the axle on, and my fingers to put on the wheels. It works perfectly now

first-removed all axles from one side of rack. replace with new ones, replace rollers. repeat for other side of rack. VIOLA!!

FIrst I shut the water and power off. I took 4 screws off bottom panels of dishwasher. Using pliers I move spring clip of the rubber valve. I disangage the hose and disconnected electrical connection ( two wires ) . Then using two open wrenches ( 3/4" and the other probably 13/16" - not sure ) disconnected the copper tubbing. I replaced the valve i reverse order.I used teflon tape for sealing connections . Everything works good now.