KUDK01ILBS1 KitchenAid Dishwasher - Instructions

Checked the house circuit breaker, verified AC to the box under the dishwasher, removed the screws around the inside door cover, and removed the cover. Removed the outer circuit board cover. Used a multi-meter to verify AC to the door latch, and to verify the latch switch was working. Verified AC to the thermal fuse above the circuit board when the door latch was closed. Verified no AC on the other side of the thermal fuse. Removed the thermal fuse connections with pliers. Used thin flat blade screw driver to unsnap the thermal fuse assembly. Used multi-meter to verify no continuity through the fuse. Ordered the fuse assembly and replaced. Reconnected the thermal fuse connections. Manually closed door switch and saw lights on the display panel, and dishwasher started. Replaced all covers and works great.

I removed the dishwasher from under the counter. This took the bulk of the repair time along with disconnecting the water supply and electrical connection. I had enough slack in drain hoses that I could turn the dishwasher over to replace the motor. I was surprised that there was only one bolt that held the motor in place. I put the motor on, turned the dishwasher upright and slide it back unde the counter and began the long process ofreconnecting everything. I am sureit could have gone faster if I were younger and did not need glasses for close work. Start to finish took me four hours. This was the fourth time I have replaced motors in dishwashers of various makes.

The part snaps on using two plastic retainers (included). You have to pull down gently on the feed tube at the top of the dishwasher to set the top retainer. After that it's a piece of cake.

Partial disassembly determined thar the plastic handle was broken and a tensnioning spring was missing (had fallen out of reach within door) Ordered new replacement parts and received next day. Great delivery service. Installed in short time by removing four screws, disconnecting two wires and reversing procedures to reassemble. Finding parts on line was a great help and the delivery service was great,

Need torx to remove front panel. There are four screws that hold the control panel that don't need to be removed. If you do remove them, it helps to put the control panel back before you reinstall the front. The six screws that hold the soap dispenser are a very small hex (<1/4, maybe 3/16). It would help to have some small sockets or nut drivers handy for this.

The door balance is easy.

Replaced the switch, that did not fix it, but a new circuit card did

Removed back of door to access the screws holding on the air inlet. The top of the door with the controls does not need to be removed, I found out--only the bottom part. Accessing the 5 screws was difficult as there was no space to get the socket onto the screws at a 90 degree angle. Also, there are two plastic shields that fall off when you remove the inlet that need to be replaced, with difficulty because of the accessibility to the area.

PartSelect site is excellent and finding the correct part was relatively simple, although I was not absolutely sure I ordered the right part until it arrived--only one day after ordering, although I paid for the least S&H option.

After replacing broken door cables I had a small leak at the door corner. I replaced door seal with that not fixing the leak and found that the door hinges were bent a little from the cables being broke for awile. Installed new hinges and leak is fixed now. A little difficult but once unit was pulled out about 6 inches the hinges were not bad to replace

Looked at other side of top rack which still had the stop. Just had to orient the direction of the stop and push it firmly onto the rack arm. Took a couple tries, but it went in and locked. Works perfectly. Inexpensive and easy fix to to very annoying problem.

Found the gasket to be wearing out. Once I got the part I took everything apart inside to find that I could have just taken the dishwasher out and replaced from the bottom. It was not difficult, but I've installed a ton of dishwashers. For the average homeowner, this is can be a difficult job since it requires plumbing and electrical skills.

The repair would have been really easy if the parts replaced had come all in one...When you order a replacement handle they do not include the 2 small springs....
the springs are a bit hard to get on, but once they were in place everything went well. You need 2 people to assemble it.
One to hold the door and the guts of the electronics, and the other to install the handle.

1) clear out the dishwasher
2) remove unit securing screws from top or sides of DW and cabinetry near the top or under the counter top
3) gently pull the dishwasher from the cabinetry about 20" is plenty, mind the connecting hoses and electrical connection
4) close the door! pull back the insulation from the area of the hinge and photograph both sides - this will save you the pain of going online
5) you will see the cord, the tensioning wheel assembly and the door balance spring on both sides
6) with the door closed to relieve tension on the cord, remove the cord from the balance spring - this can be done w/o tools at this point
7) remove the 5/16" screw from the plastic tensioning wheels and remove the tensioners, cord - leave the springs in place if not replacing them
8) install the door end of the cord to its hook on the hinge, install the new tensioning wheel assembly, install the old 5/16" self tapping screw through the lower wheel and into the outer hole in the frame
9) thread the cord from the door over the upper wheel and lower wheel. the lower wheel has cord retaining tabs to hold the cord on the assembly
10) hook the eye end of the cord to the balance spring and you are finished with the first side - repeat operations for the other side, reposition the insulation and slide the washer back in its cavity - do not forget to reinstall the stabilizing screws in the upper washer frame
11) you've done it!
12) have a cuppa and do your second washer that hasn't failed yet - it will soon.

1. do not order or buy anything before examining the tension nut and washer. 2. Unplug the unit. 3. Open the switch box before trying to remove the float. Two types; easiest is pin based and lifts out easily. If the float catches, it likely has a headed bottom and needs an assist to lift past the stop flanges. 3. Using a standard ohmmeter, check for continuity. If it checks no need to replace. 4. Check float and assembly for abnormalities; cracks, lime deposits, etc. 5. Now decide what needs replacing. Did all my work with relative ease without pulling out the appliance. A couple sequences may need realigned.

I did not relize that the drain hose was in two parts. Naturally I ordered the wrong half. So after I relized my mistake, I re-ordered the correct part. Once the correct part was received the repair was easy and went well.

Pulled front panel and replaced door switch. Extremely easy but did not fix the problem.