KUDC02IRBL2 KitchenAid Dishwasher - Instructions

Remove front door panel, replace B-metal fuse.

Needed to replace whole soap dispenser unit. Had to take front door apart cause the hex screws are on the inside. (10 Screws) then doors falls off onto floor if not careful. Spring loaded inner door wants to go up and outside door wants to fall off pulling on wiring. Unplug wiring to solinoid,(plug has locking release lever that needs to be pulled on) remove 6 hex screws, and dispenser comes out. Install new unit with 6 screws, plug in, and get help holding door parts together while installing the 10 screws. You are now finished. Pros are you get the complete unit, and not a bunch of parts. Cons are no diagrams or instructions/no new 6 hex head screws-reuse old ones. . . . . . Do not use soap powder/causes damage to latch parts/use only liquid soaps. . .

Just snapped the new retainer onto the side tines. It holds the rear tines upright on the bottom dishrac.

too simple to describe

Be sure to shut the power off before you attempt this first step, there are electrical connections all around this area. At first I didn't realize to get at the door handle I only to remove the top four screws on the inside of the door. After figuring this out the job was fairly easy. Once inside the top part of the door, all I had to do was snap off the old handle and snap in the new one. Test it to see if it works before you shut the door.

Replace motor/pump assembly

Shut off circut breaker. . . Removed 6 screws. . . Lifted cover over control board. . . Removed old control board. . Installed new board. . Replaced cover and the 6 screws. . Turned on circut breaker. . . Turned washer on. . . . It worked. Thank you for the quick delivery!

I peeled off the old seal and replaced with the new seal. The instructions were clear and easy to follow, however the new seal made the door not stay closed as the friction catch at the top was no strong enough to overcome the tension of the door closed with the new seal.

There were explicit instructions on the way the seal was to work with the sealed edge spreading into the tub area as the door closed. I was very careful to follow those instructions and made sure to seat the seal carefully. After I reinstalled the seal three times to see if I could get it to seat properly, as a last ditch effort I reversed the seal to the opposite way the instructions indicated and it worked with the door closing properly and the seal didn't leak.

Based on looking at the old seal and how it was originally installed, I actually think the seal was out of spec for the unit. However, if it isn't leaking that is what it's all about so we will see how long it holds.

Pulled everything out the front, and dug down to find a thrashed chopper assembly (like a little garbage disposal). The previous owner just tossed anything in; pop tops, plastic cutlery, etc.
Didn't pay attention to the exact installation of the chopper as I pulled it out, but, it turns out that it only goes in one way.
Used pictures and instructions I found online as a guide and didn't have any issues.
Replaced the check valve because it isn't expensive and I was in the neighborhood.

The repair was really easy. First disconnected electricity staring with fuses and removing wires from dishwasher, then disconnected drain hose and water hose. Pulled it out and removed pump turning clockwise no need for tools and same way installed new one. Very easy

Remove upper tray and spray arm. Remove two screws retaining pipe for upper spray arm and overhead. Unscrew retainer on top of lower spray arm and remove. Gently rotate the upper feed pipe clockwise until pipe can be removed from lower pipe. You may then remove the lower pipe and bearing housing where the seal is. Reverse order for reassembly. I also replaced upper spray arm bushing. Very simple, remove one screw and the arm will come out.

I found instructions on line when I goggled my dishwasher name and model number with the words noisy door. There were three or four good suggestions at a couple of the sites I visited. I tried applying vasoline, then silicone to the rope where it travels through the plastic guides but that just cut the sound down about 50%. My dishwasher has plastic guides that look like rollers but they don't turn, they are fixed in place. The ropes squeak as the pass over the guides. The replacement part kit has plastic guides that turn like wheels now so the rope does not drag over them and squeak. This repair could be done by me in 20 minutes or less every time now that I know what I am doing.

I removed the black bottom metal cover then turned the nuts on the adjusting (leveling) bolts to lower the front end of the dishwasher so I could pull it out of the cabinet. Once I lowered is as low as it would go I opened the door and pushed down on it which tilts the dishwasher down and you pull out on it and the top lip clears the cabinet. If your dishwasher just pulls out the first time you try these steps may not be necessary.
Once the dishwasher is out the guides and rope are down at the bottom in the front by the door. It's obvious what to do to replace them.

1.Check the lines for any obstruction. Gunk can easily build up. I have used the dishwasher for approx. 10 years. I do rinse/scrap dishes prior to loading.
2. Drain all remaining water.
3. Unplug the dishwasher.
4. Grab a towel and proper screw driver. Unscrew the bottom protective plate. Remove the insulation plate.
5. The drain pump is located to the bottom left. Have your towel under it. Unplug it gently. Turn counter clockwise to remove.
6. Install the new drain pump (reverse order)
7. Return the insulation plate. Screw back the bottom protective plate.
8. Plug in

Cut power and turn off water. Pulled the dishwasher out of the cabinet. Removed internal spray unit. Lay a plastic bag on bottom of tub in case a screw falls from upper spray assembly while removing. Disconnected and drained all hoses. Put down plastic lined tarp on floor. Lay dishwaser on its side onto tarp. Removed hose from recirculation pump, removed water sensor and recirculation pump from housing and detach electric connection. Removed 3 plastic push clips and removed entire motor-pump unit from tub. Position new motor-pump unit into tub. Replace 2 push clips into position, then used a flat screwdriver to put some tension and position plastic pump assembly so I could insert 3rd push clip into position. Replaced all components & reconnect hoses. Turn on water & power. A relatively simple repair. Too bad the original motor-pump only lasted 3 years. Not built like the used to. Thank goodness for Part Select.com Great schematics and descriptions. Excellent website, service, delivery and excellent Part! Thank You!

1) Remove the racks

2) Unattach the feed tube the runs from the bottom of the dishwasher tub along the back to the top (this is the grey plastic tube that the top rack sprayer plugs into). This is done by unclipping the tube in two places, one stainless clip is in the back of the tub and one stainless clip is on the top of the tub.

3) After the tube is loosened from the clips, give the tube a 45° twist clockwise (relative to the bottom of the tub) and then pull up. This should remove the entire feed tube and bottom sprayer assembly.

4) There are now 4 stainless steel torx screws visible on the bottom of the tube. Remove the screws using a torx driver. Remove the grey plastic "gear looking" piece that was held in by the screws by pulling straight up.

5) On the left hand side of the tub you will see one more (smaller) torx screw. Remove this screw and then with a pair of plyers, give the housing piece that was held on with the screw a tug straight upwards. There is a post sticking straight up that will help you do this.

6) The grinder assembly is now visible, and in my case, completely jammed with paper. Pull the grinder and screen out of the groove it is sitting in.

7) Place the new grinding and screen into the groove. The grinder blade will have to be pull back (toward you) so the grinder coupling teeth can properly engage with the motor coupling teeth. This may take some fiddling.

8) once the grinder is installed, reverse all the steps starting at step 5.