KUDA23SYWH2 KitchenAid Dishwasher - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Madolyn from Elkmont, AL
- Parts Used:
- 4171544
- Difficulty Level:
- Easy
- Total Repair Time:
- Less than 15 mins
Rubber water tube had worn out.
I just slipped the old, worn out tube off, warmed the new one in some hot water for a few minutes to make it more pliable, sprayed some non-stick spray on the end connecting in the back, and slipped it on. Piece of cake!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Colleen from Tualatin, OR
- Parts Used:
- 4171544
- Difficulty Level:
- Easy
- Total Repair Time:
- Less than 15 mins
No water was getting to the upper rack of the dishwasher
I removed the old tube by hand (it fell apart) I just worrked the new softer tube over the openings on each end and it was fixed! I did have to warm the new tube with warm water to squeeze it over the tubes but it was easy!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- ELLEN from TUSCALOOSA, AL
- Parts Used:
- WP4162322
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
dishwasher rack rusted
It was easy to remove rack from dishwasher. I screwed on rollers and it was like new!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Steven from Norton, MA
- Parts Used:
- 4171544
- Difficulty Level:
- Easy
- Total Repair Time:
- Less than 15 mins
Glasses on top rack of the dishwasher had soap film on the inside. The rubber distribution hose under the top rack had rotted and split. Didn't see it right away because it split on the bottom.
Part was easy to locate on the website. Photo on the measurement grid was the key after entering the maker and model number. I have found refrigerator parts the same way on this site. Sliced the old rotten hose to remove it. The new hose only had to be slipped over the connections. I soaped the ends of the tube to make the installation easier.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Rene from New Berlin, WI
- Parts Used:
- 4171544
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Rubber Water Delivery Tube had decayed over time.
Manually remove old tube and simply replace with new tube - no tools!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Michael from buffalo, NY
- Parts Used:
- 4171544
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
upper rack propeller jets lost power
I removed the old, brittle and leaky water delivery tube by hand and at the outlet and at the inlet end, by cutting it away with an exacto knife. I then heated the new tube under hot water and coated each end with dishwasher soap. With only a modest amount of manipulation, both ends slipped easily into place and the hose was immediately secure and operable. My wife, who didn't witness my efforts, thought I was a genius.
Was this instruction helpful to you?
Thank you for voting!
Missing Items
Simply replaced the wheels/axiles and brackets using functioning ones as template. No problem at all.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Michael from Beverly Hills, MI
- Parts Used:
- 4171544
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Hole in the water delivery tube
Pulled off old tube and slipped on new one.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Anita from CAPE MAY, NJ
- Parts Used:
- WP4172117
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Replacement for rusting 40 yr old rack
Tranfered wheels from old rack to replacement rack. Silverware caddy was a bit too big for the replacement. I gently bent the prongs on the rack a little and its fits perfect.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Elmer from YORKVILLE, IL
- Parts Used:
- 675806
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 1- 2 hours
1/4 inch bolt frozen to shaft
The 1/4 inch impeller bolt to shaft would not budge with a nut driver so I had to use a ratchet to loosen it. I could not hold the drain impeller with an adjustable wrench so I had to use a vice-grip. This still did not loosen it so I used an oscillating power saw to cut away at the bottom of the drain impeller being careful to only cut so deep, I didn't want to cut into the motor shaft. Once I had cut some grooves into the drain impeller, I could break it into pieces and remove it. Upon reassembly I tightened the 1/4 inch bolt with the ratchet.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Mollie from CANTON, NC
- Parts Used:
- W10586589
- Difficulty Level:
- Very Difficult
- Total Repair Time:
- More than 2 hours
Insulation needed replacing
I searched for the 18x5x5 insulation.,ordered it from Part Select. Waited. Company sent wrong part. Called, they gave me a refund, reordered, promised 2 day free shipping. Waited more than a week, paid for 2 day shipping. Received same, wrong part. Still don't have repair done. Looking elsewhere for part.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Allen from MOUNT VERNON, WA
- Parts Used:
- WP4160355
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
Replacing broken door hinge guide bearing sleeve
Repair was awful without instructions. Instructions were requested twice with no response. Attempted without instruction and broke the sleeve. Reordered but not through Partselect
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Aubrey from BERKELEY LAKE, GA
- Parts Used:
- 675806
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Pliers, Screw drivers, Socket set
The Cutter Spring was totally disfigured and pulled apart. Not functional.
Repair went exactly like the video i watched online. Perfect
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- B Jean from MONTPELIER, OH
- Parts Used:
- WP302711
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers
throwed water out under the door
Did not use the new parts. After removing the spray arm, found a screw out of place. Put the seal ring back in place and the screw back in the hole. Machine works like new.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Walter from KINGSPORT, TN
- Parts Used:
- 675806
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 1- 2 hours
- Tools:
- Nutdriver, Screw drivers, Socket set, Wrench (Adjustable)
i had a leak under the dishwasher when the pump turned on.
I replaced the seals per the video instructions.
Was this instruction helpful to you?
Thank you for voting!